### Understanding Hydraulic Jacks**Question:**In a hydraulic jack, your input force is increased at the output if you push down the piston having __________.**Answer Options:**- ○ the smaller area.- ○ the larger area.- ○ it doesn’t matter which piston I am pushing down.- ○ it depends only on the fluid present.### Explanation:Hydraulic jacks operate based on Pascal's law, which states that pressure applied to a confined fluid is transmitted undiminished to every point of the fluid and to the walls of its container. The force applied to a smaller-area piston results in a greater force at the larger-area piston, thus lifting heavier loads with less effort.

Name: ### Understanding Hydraulic Jacks**Question:**In a hydraulic jack, yo
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: ### Understanding Hydraulic Jacks**Question:**In a hydraulic jack, your input force is increased at the output if you push down the piston having __________.**Answer Options:**- ○ the smaller area.- ○ the larger area.- ○ it doesn’t matter which pist

Hydraulic Jacks have many applications: They are used to lift cars, to lift heavy loads in the…

Science

Physics

In a hydraulic jack your input force is increased at the output if you push down the piston having the smaller area. the larger area. it doesn't matter which piston I am pushing down. O it depends only on the fluid present.

In a hydraulic jack your input force is increased at the output if you push down the piston having the smaller area. the larger area. it doesn't matter which piston I am pushing down. O it depends only on the fluid present.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

a stiff, 15-cm-long tube with an inner diameter of 3.5 mm is attached to a small hole in the side of a tall beaker. the tube sticks out horizontally. the beaker is filled with 20⁰c water to a level 50 cm above the hole, and it is continually topped off to it maintain that level. What is volume flow rate through the tube? The viscosity of water is 1.0×10^-3 Pa×s.
AST Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y 12.5 cm below point 1. The water pressure at point 1 is 3.20 x 10 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 x Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. m/s (b) point 2 x Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. m/s
a.) What minimum force must you exert to lift a car of mass 1500 kg. Ifrout = 0.71 m and Ain = 0.2 m²? b.) If you want to raise the car %3D by 25 cm, how far will you have to move the input piston? Force distance A) 1563 N 154 cm B) 1856 N 198 cm C) 2463 N 143 cm D) 2648 N 174 cm A C В A c) D В
An object will sink if its weight is ……………the buoyant force. Similar to and almost equal Different from and almost equal Less than or equal to Greater than
Verify that work input equals work output for a hydraulic system assuming no losses due to friction. Do this by showing that the distance the output force moves is reduced by the same factor that the output force is increased. Assume the volume of the fluid is constant. What effect would friction within the fluid and between components in the system have on the output force? How would this depend on whether or not the fluid is moving?
Calculate the Reynolds number for an object moving through a fluid.
Method of work: - Prosegare 1- Weigh the solid body with air (let it be a cylinder of known size) w1 2- Weigh the body while it is immersed inside the device without touching the walls or bottom of the beaker w2 3- We calculate the volume of the displaced fluid v Note that the weight of the weight = 200 gm, the density of water = 1, and the volume of the displaced liquid = 23 Calculations: - Calculation 1- The volume of displaced water (v cm3) and a comparison with the volume of the cylinder. 2- Calculate the weight of the body while suspended in the air 2 gravity acceleration cm Eyawl=gm s2 g= m=( ) gm mass of soild ст wl=( ) gm dyne s2 3- Calculate the weight of the body while it is immersed in water cm w2=( ) gm s2 4 - Calculate the difference in weight wl-w2 ( ) dyne 5- Calculate the weight of the displaced fluid volume = volume*density*acceleration v*p*g v() cm3 -: üleya p = ( ) gm ст3 ст g=( ) s2 ст v* p*g =( ) gm s2
A fusiform aneurysm bulges or balloons out an artery on all sides (pictured below). If this aneurysm occurs in an aorta, the internal radius may increase from r₁ = 1.1 cm in the normal, healthy section to 12= = 2.2 cm in the diseased section (while staying at the same vertical height). The speed of blood m flow is v₁ = 0.42 in the normal section and the gauge pressure P₁ is 99.98 mmHg. The density of 1 S blood is 1060 kg m³ Fusiform Aneurysm Image from: http://www.okclipart.com/Fusiform-Aneurysm-Clip-Art30koqyaskv/ (a) Calculate the speed of blood v2 in the aneurysm. Answer to two significant figures. Think: What equations dictating the flow through the valve are valid, equation of continuity, Bernoulli or Poiseuille? What simplifications should you make regarding the blood flow. m V₂ = S (b) Calculate the pressure gradient AP = P aneurysm healthy aorta from the healthy aorta into the aneurysm. Think: What equations dictating the flow through the valve are valid, equation of…
A water main broke on Lake Shore Drive in Chicago on November 8, 2002, shooting water straight upward to a height of 8.0 ft. What was the pressure in the pipe?
BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 10 - 21
(c) Water is circulating through a closed system of pipes in a two-storey house. On the ground floor, the water has a gauge pressure reading of 3.5 × 105 Pa and has a speed of 2.1 m/s. However, on the upper floor, which is 3.8 m higher, the speed of the water is 3.7 m/s. The pipe widths are different on the two floors. Calculate the pressure of the water on the upper floor of the house? Take the density of water to be 1000 kg/m
If a fluid's speed increases, what happens with its pressure and how do you know?