Answered: A cylinder with a bore diameter of 4.5… | bartleby

Related questions

Question

A cylinder with a bore diameter of 4.5 inches and a rod diameter of 1.5 inches is to be used in a system to extend the cylinder against a load of 16000 lbs. The pressure required to extend the cylinder:

a) 905.1psi

b)1131psi

c)790.1psi

d)1006psi

e) none of these

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A waste management company handles large dumpsters of construction debris. The sorting process starts by downloading the dumpster from the transport truck and then dumping its contents into a large hopper as shown below. The waste management plant uses a hydraulic cylinder arrangement to tilt the dumpster to the point that the force of gravity will empty the contents. The plant operator activates an electric pump that pumps hydraulic oil into the input piston at an absolute pressure of 2.50 x 106 Pa and drives the output plunger, which has a radius of 0.230 m. If the design of the dumping arrangement is such that the output plunger remains perpendicular to the floor of the dumpster, determine the torque the plunger creates about an axis at the end of the dumpster. Enter a number. Frect pressure to use for the pressure in the oil at the site of the input piston? According to Pascal's Law, how is the pressure in the oil at the site of the output plunger related to the pressure in the oil…
A rectangular aquarium having a length of 3meters, a width of 1 meter, and a height of 2meters is filled to the top with water. Giventhat water has a density of 1000 kg per ?^3,find the work required to pump all of thewater over the top edge of the tank.
A room has a width of 14.1 feet, a length of 15.5 feet, and a ceiling height of 12.0 ft. The average flow rate for this room's air conditioning unit is 3.07 m^3/s. How many SECONDS will it take for the air conditioner to cycle the volume of air in the room?
4) The turbine extracts 0 hp from the water flowing through it. The pipe with diameter of 1 ft and length of 300 ft is assumed to have a friction factor of 0 02. Minor losses are negligible. Determine flowrate through the pipe and turbine? Head losses is h₁ = 85 ft ▼ Imad ti EBOOK (1) 1 = 90 ft 300-ft-long, 1-ft-diameter pipe f = 0.02 Turbine (2) Free jet 42 = 0
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.700 L/s, with an output pressure of 2.00 x 105 N/m². You may neglect frictional losses in both parts of this problem. (a) The water enters a hose with a 3.00 cm inside diameter and rises 3.00 m above the pump. What is its pressure (in N/m²) at this point? N/m² (b) The hose goes over the foundation wall, losing 1.70 m in height, and widens to 4.00 cm diameter. What is the pressure now (in N/m²)? N/m²
Water flows at 1 m/s from a hot water heater, through a 410 kPa pressure regulator. The pressure in the pipe supplying an upstairs bathtub 3 m above the heater is 350 kPa. What’s the speed in this upstairs pipe? (Numerical answer is assumed to be in m/s)
1. Find kinetic energy per cubic meter of flowing blood (V =1 m') in aorta for individual at Q = 5 liter/min, radius of aorta 1 cm. The density of blood is rest. Suppose flow rate is about p-1.05-10' kg/m. R =
the water faucent for a garden hose is tuned on, but with the nozzle turned off the owner of the garden assumes that the water cannot exit the hose. however , even through the hose lies horizonatlly on the ground, the owner notice a stream of water spraying vertically out a small leak in the hose. to a height of 0.75 m. what must be the pressure of the water inside the hose 1) 7.9 kpa 2) 8.8 kpa 3) 7.4 kpa 4) 101.3 pka
What pressure is exerted on the bottom of a 0.500-mwide by 0.900-m-long gas tank that can hold 50.0 kg of gasoline by the weight of the gasoline in it when it is full?