In a downtown office building, you notice each of the four sections of a rotating door has a mass of 85 kg. What is the width, in meters, of each section of the door if a force of 66 N applied to the outer edge of a section produces an angular acceleration of 0.460 rad/s?? Additional Materials Reading

In a downtown office building, you notice each of the four sections of a rotating door has a mass of 85 kg. What is the width, in meters, of each section of the door if a force of 66 N applied to the outer edge of a section produces an angular acceleration of 0.460 rad/s?? Additional Materials Reading

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Rotational Dynamics

Section: Chapter Questions

Problem 32P: If the system shown in Figure P8.37 is set in rotation about each of the axes mentioned in Problem...

See similar textbooks

Similar questions

An electric sander consisting of a rotating disk of mass 0.7 kg and radius 10 cm rotates at 15 rev/sec. When applied to a rough wooden wall the rotation rate decreases by 20 . (a) What is the final rotational kinetic energy of the rotating disk? (a) How much has its rotational kinetic energy decreased?
A large grinding wheel in the shape of a solid cylinder of radius 0.330 m is free to rotate on a friction less, vertical axle. A constant tangential force of 250. N applied to its edge causes the wheel to have an angular acceleration of 0.940 rad/s2. (a) What is the moment of inertia of the wheel? (b) What is the mass of the wheel? (c) If the wheel starts from rest, what is its angular velocity after 5.00 s have elapsed, assuming the force is acting during that time?
A uniform cylindrical grindstion has a mass of 10 kg and a radius of 12 cm. (a) What is the rotational kinetic energy of the grindstone when it is rotating at 1.5103rev/min ? (b) After the grindstone’s motor is turned off, a knife blade is pressed against the outer edge coefficient of kinetic friction between the grindstone and the blade is 0.80. Use the work energy theorem to determine how many turns the grindstone makes before it stops.
A uniform cylindrical grinding wheel of mass 50.0 kg and diameter 1.0 m is turned on by an electric motor. The friction in the bearings is negligible. (a) What torque must be applied to the wheel to bring it from rest to 120 rev/min in 20 revolutions? (b) A tool whose coefficent of kinetic friction with the wheel with a force of 40.0 N. What torque must be supplied by the motor to keep the wheel rotating at a constant angular velocity?
A rope of negligible mass is wrapped around a 225 kg solid cylinder of radius 0.400 m. The cylinder is suspended several meters off the ground with its axis oriented horizontally, and turns on that axis without friction, (a) If a 75.0-kg man takes hold of the free end of the rope and falls under the force of gravity, what is his acceleration? (b) What is the angular acceleration of the cylinder? (c) if the mass of the rope were not neglected, what would happen to the angular acceleration of the cylinder as the man falls?
A bar on a hinge starts from rest and rotates with an angular acceleration = 10 + 6t, where is in rad/s2 and t is in seconds. Determine the angle in radians through which the bar turns in the first 4.00 s.
A constant net torque is applied to an object. Which one of the following will not be constant? (a) angular acceleration, (b) angular velocity, (c) moment of inertia, or (d) center of gravity.
The angular speed of a wheel is given by (t) = 72.5 rad/s + (9.34 rad /s2) t. a. Is the wheels angular acceleration constant? Explain. b. Find an expression for the angular acceleration.
The combination of an applied force and a friction force produces a constant total torque of 36.0 N m on a wheel rotating about a fixed axis. The applied force acts for 6.00 s. During this time, the angular speed of the wheel increases from 0 to 10.0 rad/s. The applied force is then removed, and the wheel comes to rest in 60.0 s. Find (a) the moment of inertia of the wheel, (b) the magnitude of the torque due to friction, and (c) the total number of revolutions of the wheel during the entire interval of 66.0 s.
An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
A turntable (disk) of radius r = 26.0 cm and rotational inertia0.400 kg m2 rotates with an angular speed of 3.00 rad/s arounda frictionless, vertical axle. A wad of clay of mass m =0.250 kg drops onto and sticks to the edge of the turntable.What is the new angular speed of the turntable?
Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23