Impedances are marked in perunit on a 100MVA, 100 KV base. The load at bus 2 is S2= 16MW - j32 MVAR, and the load at bus 3 is 50MVA at 0.8 pf leading. It is required to hold the voltage at bus 3 at 100 KV. V1 V2 V3 j0.4 pu j0.5 pu S2 S3 taking V3 as phase reference, the voltage at bus 2 is V2= and the voltage at bus 1 is V1=

Impedances are marked in perunit on a 100MVA, 100 KV base. The load at bus 2 is S2= 16MW - j32 MVAR, and the load at bus 3 is 50MVA at 0.8 pf leading. It is required to hold the voltage at bus 3 at 100 KV. V1 V2 V3 j0.4 pu j0.5 pu S2 S3 taking V3 as phase reference, the voltage at bus 2 is V2= and the voltage at bus 1 is V1=

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Two impedances Z1 = 3 + j4 and Z2 = 5 – j8.66ohms respectively are connected in parallel. If the combination is connected across a 240 V AC Source, how much is the total current? a. 44.4 A b. 42.1 A c. 40.6 A d. 39.9 A e. none of the above
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
Q: For the following SLD, take Sg = 100 MVA and VB = 22 kV at Bus 1to:1. Draw the impedance diagram with all impedances in pu2. Find Em- 30 MVA40 MVA30 MVAX= j0.6 puX= j0.3 pu(40:15) kV18 kV(15:35) kVEgEmX= j0.3 pu(3+j4) QT.L50 MVA Ti Bus 1Bus 2 T2Load40 MVA23 kVBus 318 kVX = j0.5 pupf = 0.65 lead
Given at the load: Vioond = 452-25° VRMS, 452-25° VRMS, Iload What are the real and reactive power and power factor at the load? Exclude the units. real power: reactive power: power factor: Iload-10-25 ARMS what type of impedance is seen at the load? R. L. or Ch
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
and the new peru impedance of the motor is a load absorbs 50 MVA at 0.8 pf leading at line to line voltage of 18 KV. find the perunit impedance of this load on a base of 100MVA and 20 KV. Select one: O a. 5.183 - j 3.888 pu O b. 5.183 + j 3.888 pu O c. 1.295 - j 0.972 pu O d. 1.295 +j 0.972 pu O e. None of these
Pz:- The of abalanced Y connected load is- Each phase of the load cousist of loL30 s2 Find the Line Voltages at the terminat actives Reachive and somflex Power Per Phase then Find the total Powers For Heree phase load. VAB =10010for 4
Find out the zero-phase sequence components of the following set of three unbalanced voltage vectors: Va =10cis30° ,Vb= 30cis-60°, Vc=15cis145°" (THOS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE THE LETTER WITH THE CORRECT ANSWER AND PLEASE PROVIDE YOUR CLEAR SOLUTION! A 16.809cis-72.579° B 5.603cis72.579° C 16.809cis-47.421° D 5.603cis-47.421°
15) Kirchhoff's Voltage Law (KVL) states that A) the product of the phasor voltages around any closed path must equal zero. B) the sum of the phasor voltages around any closed path does not have to equal zero. C) the sum of the phasor voltages around any closed path must equal zero. D) the sum of the phasor voltages around a closed path cannot include "through the air."
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
Īs L₁ ~ Load 1: 200 W, unity power factor Load 2: 1200 W at 0.85 power factor lagging Load 3: 400 W + j100 VAR Load 4: -200 VAR । [+ L₂ L3 L4