(III) A door 2.30 m high and 1.30 m wide has a mass of 13.0 kg. A hinge 0.40 m from the top and another hinge 0.40 m from the bottom each support half the door's weight (Fig. 9–69). Assume that the center of gravity is at the geometrical center of the door, and determine 40 cm 2.30 m the horizontal and vertical force components exerted by each hinge on the door. -1.30 m- F40 cm FIGURE 9-69 Problem 29.

(III) A door 2.30 m high and 1.30 m wide has a mass of 13.0 kg. A hinge 0.40 m from the top and another hinge 0.40 m from the bottom each support half the door's weight (Fig. 9–69). Assume that the center of gravity is at the geometrical center of the door, and determine 40 cm 2.30 m the horizontal and vertical force components exerted by each hinge on the door. -1.30 m- F40 cm FIGURE 9-69 Problem 29.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: 5-75. If the cable can be subjected to a maximum tension of 300 Ib, determine the maximum force F…

Q: One end of a uniform l = 3.80 m long rod of weight supported by an angle of theta = 37 degrees with…

Q: A uniform rod is attached to a wall by a hinge at its base. The rod has a mass of 7.5 kg, a length…

A: The mass of the rod is The length of the rod is The angle of the rod with the horizontal is

Q: stress within the

Q: (24) Assuming the lower arm has a mass of 2.8 kg and its CG is 12 cm from the elbow- joint pivot,…

A: Given, mass of the shot put, m = 7.5 kgmass of the lower arm, M = 2.8 kgcenter of gravity of lower…

Q: A person is standing on a level floor. His head, upper torso, arms, and hands together weigh 437N…

A: Given data The weight of the upper part is W1 = 437 N The center of gravity of the upper part is x1…

Q: A carpenter and his assistant are to carry a uniform wooden beam, which is 6 m long and weighs 100…

A: Draw the free-body diagram of the system.

Q: Why must the change in the wire's length be measured so accurately although the wire's original…

A: Write the expression for the strain and stress, respectively.

Q: 3) A uniform board 7.5 m long with a mass of 73 kg is attached to a wall with a pivot. A rope with a…

A: See below

Q: (II) Find the tension in the two cords shown in Fig. 9-45. Neglect the mass of the cords, and assume…

A: Given, m=170 kgθ=330

Q: 1) A tapered log 3.0 m long weighs 210 N and has its center of gravity 1.0 m from the thick end. It…

Q: (II) Find the tension in the two cords shown in Fig. 9-45. Neglect the mass of the cords, and assume…

Q: One and of a uniform 3.30-m-long rod of weight is supported by a cable at an angle of 8-37 with the…

Q: (c) Find the vertical force exerted on the base of the rod. Ignore the weight of the rod. magnitude…

Q: A wire is stretched between two poles 28.0m apart. A sign is attached at the midpoint of the wire…

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A: Given: To find Force P

Q: A 15,000 N crane pivotsaround a friction-free axle atits base and is supported by acable making a…

A: Ans.(a) Find the moments around the axle. Take clockwise as positive. For the system to be in…

Q: uniform beam of length ? and mass ? is inclined at an angle ? to the horizontal. Its

Q: 5. Two identical, uniform beams of length 3 m and weighing 260 N each are connected at one end by a…

Q: The mobile in Fig. 12–74 is in equilibrium. Object B has mass of 0.748 kg. Determine the masses of…

A: Given:- The figure is in equilibrium. Object B has a mass = 0.748 kg Find:- Determine the mass of…

Q: (II) A 75-kg adult sits at one end of a 9.0-m-long board.His 25-kg child sits on the other end. (a)…

Question

(III) A door 2.30 m high and 1.30 m wide has a mass of
13.0 kg. A hinge 0.40 m from the top and another hinge
0.40 m from the bottom each support half the door's weight
(Fig. 9–69). Assume that the center
of gravity is at the geometrical
center of the door, and determine
40 cm
2.30 m
the horizontal and vertical force
components exerted by each hinge
on the door.
-1.30 m-
F40 cm
FIGURE 9-69
Problem 29.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A 2.0-m-high box with a 1.0-m-square base is moved across a rough floor as in Fig. 9–89. The uniform box weighs 250N and has a coefficient of static friction with the floor of 0.60. What minimum force must be 1.0 m exerted on the box to make it slide? What is the maximum height h above the floor that this force can be applied without tip- ping the box over? Note that as the box tips, the normal force CG 2.0 m FN and the friction force will act at the lowest corner. Fir FIGURE 9-89 Problem 74.
The uniform 19.0 kg beam below is 6.4 m long and is perfectly balanced about a point 1.4 m from the left end. What is the mass of the block? (Hint: when calculating the torque due to the weight of the beam, consider all of its mass to be located at its center of mass.)
Why is it not possible to sit upright in a chair and rise toyour feet without first leaning forward?
.
Assume Young’s modulus for bone is 1.40×1010 N/m2 . The bone breaks if stress greater than 1.50 × 109 N/m2 is imposed on it. (i) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (ii) If this much force is applied compressively, by how much does the 20.0 cm long bone shorten?
A wheelbarrow with w weight of 150N is used to lift a load with a weight of 900 N. The length from the wheel axle to the center of gravity (COG) of the load is 2 ft, and the distance to the (COG) of the wheelbarrow is 1.5 ft. The length from the wheel axle to the hands is 5 ft. The wheelbarrow is also tilted at an angle of 30 degrees with respect to the horizontal. Calculate the motive force required to hold the wheel barrow