II. Problem Solving. Provide a complete and orderly solution to the given problem and submit your answers in pdf format. A section of a reinforced concrete elevator shaft is shown in the figure. Compute the following: a. Centroid of section; b. Centroidal Moments of Inertia; and c. Rigidity about the centroidal axes. Consider the effect of shear deflection. Assume h = 15m, P = 1000 kN, and f'c = 24 MPa. 0.40 3.24 2.83 Note: Elevator shaft dimensions are in meters. 1.12 1.12

II. Problem Solving. Provide a complete and orderly solution to the given problem and submit your answers in pdf format. A section of a reinforced concrete elevator shaft is shown in the figure. Compute the following: a. Centroid of section; b. Centroidal Moments of Inertia; and c. Rigidity about the centroidal axes. Consider the effect of shear deflection. Assume h = 15m, P = 1000 kN, and f'c = 24 MPa. 0.40 3.24 2.83 Note: Elevator shaft dimensions are in meters. 1.12 1.12

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show complete solutions
If beam as shown in Figure has a rectangular section with a depth of 100mm and width of 20mm, calculate the slope and deflection at free end. Assume E = 200GPa.where P=55
OEVALUATE The following problems are given to assess your ability to solve problems on equilibrium of force systems. Instructions. Solve the following problems, refer to your Assignment Guide on the specific guidelines on formats and how to submit your solution. 1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at A and B. B a. Draw the free-body diagram of the beam. 45 30° b. What are the magnitudes of the reactions at A and B? -1.2 m-1.5 m-1m- 2. For the beam shown: a. Draw the free-body diagram of 1.8 m 1.8 m 1.38 kN the beam. b. Determine the reactions at the supports. 0.80 kN 25 AL 1.5r 1.5m 21m m, 3. Three cables are joined at the junction ring C. Determine the tensions in cables AC and caused by the weight of the 30-kg cylinder. 45 15° 30 kg 30%
The following figure shows a simple bracket made of structural steel with Young's modulus E = 200 GPa and Poisson's ratio v = 0.3. The bracket has a cross-section profile shown below and an extrusion depth of 12 cm. A through-hole of diameter 1.5 cm is centered on the bracket's flat ends, one on each side, as shown in the figure. Suppose that the bracket is fixed on the bottom, and lifted by a pressure load of 1,296.12 N/cm² from the inside surface of the top flat portion. What is the total deformation of the bracket in mm? 10.000 1.500 1.500 R3.000 8.000 1.500 12.000 1.500 8.000 All dimensions are in centimeters. 1.500
PLEASE ANSWER I NEED IT ASAP
All information given
Solve the given problem. Round off answers in all computations in 4 decimal places. Determine the moment capacity of the beam shown in the figure.
Given the problem: The smooth disk shown in the figure is pinned at 'D' and has a weight of 24.6 lb. Neglecting the weights of the other members, determine the following: d.) Horizontal component at 'D' in lb. e.) Vertical component at 'D' in lb. *Round off final answer in 4 decimal places. Thank you.
PLEASE ANSWER CORRECTLY USE VIRTUAL WORK METHOD PROVIDE COMPLETE SOLUTIONS AND APPROPRIATE ILLUSTRATIONS BOX THE FINAL ANSWERS IN 3 DECIMAL PLACES WITH CORRECT UNITS
problem 9
Please solve the following problems with step by step solutions and show all work