A beam is supported by single journal bearings at both ends. A distributed load defined by the function W(z) = (5z² – 7z + 19) is applied to the beam. Note: the origin is located 0.5 ft to the right of ft point A. W. Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value di 0.5 ft d2 7 ft a. Determine the magnitude of the equivalent force, FR that replaces the force system. b. Determine the location of the FR on the beam, d, measured from point A. Round your final answers to 3 significant digits/figures. FR= d = ft

A beam is supported by single journal bearings at both ends. A distributed load defined by the function W(z) = (5z² – 7z + 19) is applied to the beam. Note: the origin is located 0.5 ft to the right of ft point A. W. Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value di 0.5 ft d2 7 ft a. Determine the magnitude of the equivalent force, FR that replaces the force system. b. Determine the location of the FR on the beam, d, measured from point A. Round your final answers to 3 significant digits/figures. FR= d = ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 442 mm². Determine the axial stress in each bar. B 2 m O 1 m 5Q KN 1 m O E 1 m 8T KN 1 m LL
The cross section of the beam in the figure is made of 100 mm x 20 mm boards. It is manufactured by screwing each other and the distance between the screws is 50 mm. and the shear force is V = 2500 N. Safe slipping for screw material Since the stress value is τem = 50 MPa, the screw that can be used in connection Find the diameter. dimensions in mm
Pls skip if not familiar and kindy use free body diagram for better understanding. Thank you!
Solve using Mohr circle method
Question 1 The same torque is applied to two tubes with identical metal sheets, determine the ratio of T circle/Tsquare of the shear stresses. Given: r= 14 mm, S = 19 mm, and t = 2.84 mm. 43 FETOO KA F1 F2 FS FB F7 F8 ESC T H.
A portal frame shown in figure (not drawn to scale) has a hinge support at joint P and a roller support at joint R. A point load of 50 kN is acting at joint R in horizontal direction. The flexural rigidity El, of each member is 10° kNm?, under the applied load, the horizontal displacement (in mm, round off to 1 decimal place) of joint R would be 5 m EI EI 10 m R 50 kN
SHOW COMPLETE WORK AND FBD
Problem 5 The load has a weight of 950 lb. -1.5 ft- 1 in. max = Section a - a Q Tap image to zoom Part A Determine the maximum normal stress developed on the cross section of the supporting member at section a-a. Express your answer in kilopounds per square inch to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: ksi
Current Attempt in Progress The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.25 in., -0.65 in.). Assume a = 7 ft, b = 5 ft, and h = 6 ft. Determine the normal strain in each %3D bar. a A y h B Answers: EAB %3D EBC
Using Tall = 68 MPa and G= 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. (a) (b) 45 mm 15 mm 25 mm 25 mm 900 mm B Check my work B The largest torque that can be applied at end B of bar a is N-m and the corresponding angle of twist is The largest torque that can be applied at end B of bar bis N-m and the corresponding angle of twist is
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0.0). After load P is applied. joint B moves to the coordinate position (0.35 in., -0.55 in.). Assumeo - 11 ft, b-7 ft, and h-8 ft. Determine the normal strain in each bar. Answers: CAB EBC 3676.02 i 5685.14 με με