If you were to monitor the reaction mechanism for the hydroboration by TLC (Thin Layer Chromatography), would you expect the starting material (1-octene) or the product (1-octanol) to have a lower Rf? Please explain your answer, being sure to mention important intermolecular forces. Why does the hydroboration part of the reaction have to be performed in anhydrous conditions?

If you were to monitor the reaction mechanism for the hydroboration by TLC (Thin Layer Chromatography), would you expect the starting material (1-octene) or the product (1-octanol) to have a lower Rf? Please explain your answer, being sure to mention important intermolecular forces. Why does the hydroboration part of the reaction have to be performed in anhydrous conditions?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

17) After the reaction, Gwen sees a solid appear. She should collect this solid by rotary evaporator vacuum filtration TLC gravity filtration 18) After completing the separation and purification, Gwen checks the purity of her isolated mandelic acid on a polarimeter. She takes 0.525 g of solid and dissolves it in 5 mL of acetone. She puts this in a tube with a pathlength of 1 dm. The polarimeter gives a reading of +13.0011 deg. The reported optical activity of mandelic acid is [a]lit = 151 deg What is the EE for this sample?
Question 10: What technique should Gwen use to collect the final product that forms? gravity filtration reflux vacuum filtration rotovap
2. Complete the chart below. You will need to look up Molecular Weights (MW), melting points (MP), boiling points (BP) and density. Keep in mind that liquids and solutions do not always have reported melting points (MP) or boiling points (BP). You do not need to find amounts, mmol or molar equivalence of 9-fluorenone. If the compound is a solid the boiling point (BP) and density (d) are often not reported. Molar equivalence is defined as the ratio of the moles of compound to the moles of the limiting reagent. MW MP Density Molar Compound Amount mmol BP (°C) (g/mol) °C) (g/mL) Equivalence 9-Fluorenol 100 mg 6 ml Acetone 0.25 ml Glacial Acetic Acid 1.093 NaOCI 2 ml (5% wt/wt in H,0) 9-fluorenone 3. Calculate the theoretical yield for reaction based on the chart above and the reaction scheme at the top of this assignment.
Please answer correct.
Draw the synthesis setup for Ni(dppf)Cl2, make sure to include the round-bottom flask, reflux condenser, hotplate, and the connections to the vacuum and water-cooling systems. Design an experiment remove separate Ca2+ and herbicide Atrazin (organochloride) from aqueous salt solution.
Which of the following compounds reacts fastest with the Lucas test? 5 H OH 2 ㅇ= ton 6 3 OH 7 ~ 8 4 ОН
Please, I need help to calculate the %yield of this experiment. These is my values obtained in the laboratory : volume of cyclohexanol = 7.39mL ; mass of cyclohexanol = 7.112 g mass of cyclohexanone obtained = 1.535 g Thymol blue = 3 drops volume of Sodium Bisulfite = 1mL volume NaOH used = 20mL
Reaction of 2 pentanol with zncl2/hcl? Write missing reactant, substrate, reaction conditions, product and reaction mechanism.
How can We use GC analysis to confirm the identity of the product?
Lab observation sheet synthesis of 2-Chloro-2-Methylbutane -Centrifuge cleared +10mL Centrifuge tube. -4ml 2-methyl-2-butanol added to Centrifuge tube. -5ml Hydrochloric added CT -Shaked for 3 min - Two Layers formed - aqueous layer pipetted out into the beaker set aside. - 2ml water added To CT, inverted vented few times. - aqueous layer pipet out to beaker - 2ml 5% sodium bicarbonate, added to CT, inverted and vent and aqueous layer pipet out into the beaker -Centrifuge Tube poured into a cleaned 5mL conical vial - a few scoops of soduim sulfate added to the CV and stirred well - new 5mL Conical vial with teflon stopper preweighted 25.90g - liquid decanted into the new conical vial - conical vial + liquid capped and weighted 26.40g CALCULATIONS: % YIELDS FOR the REACTION SHOW ALL WORK
I received the following question from the professor. The answer is H2SO4, NaCN for the agent and H2O for the solvent. But some people say the answer is KCN and HCN. 1. Please write down the process of solving the problem in detail. Please tell me how you found the reagents and solvents and how they are applied. 2.In addition, I would like to solve a similar problem. What should I type on the internet to find this type of problem?
State LeChatelier’s principle (HINT: Refer to a General Chemistry text)AND explain how it helps us to get a good yield in this experiment. (Dehydration of 2-Methyl-2-Butanol)