If weight of angles A & B is a AABC is W, the ratio of weight of angle C to weight of A is (a) 1 - 8 (b) 8 (c) 1 0.5 (d) 0.5

Q: 1. What king of population growth equation is more likely appropriate in a downtown area, where…

A: solving first questionslet's discuss the why population growth equation more likely to appropriate…

Q: LINE LATITUDE (m) DEPARTURE (m) АВ 100 50 ВС 200 200 CA -300 -250

A: Calculating the DMD(Double meridian distance): Double meridian distance of any line=DMD of preceding…

Q: Two surveying tapes were used in measuring the frontage of an open field. the resulting measurements…

A:

Q: Develop the following triangular inflow hydrograph through a linear reservoir: Peak inflow R m/s,…

A: To find outflow

Q: QUESTION 2 (pump characteristics) The following table provides the results of a pump performance…

A: Discharge and dynamic head is givenfind a.plot the characteristic curve b. plot the characteristic…

Q: 94444% 00962% 11702% 25000% 41892% ne of the Choices

A:

Q: Figure Ql shows a 1D flow through a two layers soil column. The soil properties and cross-sectional…

A: In soil due to its height, there will be stress that is known as the total stress in the soil that…

Q: A lighthouse is visible just above the horizon at a certain station at the sea level. The distance…

A: Given data :-The distance between the station and the lighthouse = D = 40 kmCalculate the height of…

Q: Soil Mechanics and Foundation Engineering Question if an unconfined aquifer released 5 m³ of water…

A:

Q: A beam is limited to the dimensions b = 15 in, d = 20 in,. and d' = 4 in. If Mp = 170 kip-ft…

A: We have to determine the value of limiting steel ratio maximum steel area based on steel ratio and…

Q: Engineering fill out the table by the answer. In the shown connecting traverse ABCDE, the azimuth…

A:

Q: The azimuth for line AB is 35° and the azimuth for line AC is 140°. The internal angle BAC in…

A: The azimuth of line AB = 35o The azimuth of line BC  =140o To measure internal angle BAC?

Q: 80 11 B 10 mm 10 mm 80 10 mm

A:

Q: 6. Design a circular sedimentation tank with a retention period of two hours for a town with a…

A:

Q: surveying

A: Given I=30020'(a)Length =PT-PC=(1450.4)-(1260.5)=190Length=L=πRI180190=π(R)(30°20')180R=358.885Given…

Q: Solution for #2 diagram

A: Maximum shear force will occur a fixed support = 20k Maximum bending moment will occur at fixed…

Q: The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD…

A: TAB=800N-mTBC=2400N-mTCD=2400N-m

Q: Question -4, A cylindrical specimen of saturated clay 40 mm in diameter and 80 mm in overall length…

A: Given- Diameter d=40 mm, 80 mm overall length Axial load =46.5 N Change in length at failure =1 cm,…

Q: Solution for #3 diagram

A: As per my knowledge i was answered,If you have any doubts, please comment below.Thank you👍👍…

Q: Question A vertical photograph was taken at an altitude of 2000 m above mean sea level. If the scale…

A: Given data- Altitude H=2000 m above mean sea level, Photograph elevation=250 m, Scale S=1:1000, To…

Q: 3. If the total difference in elevation of BM4 and BM1 is -5.1163 meters, find the value of X. Sta.…

A:

Q: For a colony of 10,000 persons having sewage flow rate of 200 1/capita/day, BOD of applied sewage is…

A: Given: No.  Of persons in colony= 10000 Sewage flow rate, Q = 200 l/capita/day BOD = 300mg/l =…

Q: A specific gravity test was performed on three soil samples, and the following data were collected:…

A: MaterialEmpty pyconometer (W1) (g)Weight of dry soil (W2) (g)Weight of pycnometer + water + soil…

Q: 4- Determine the vertical and horizontal deflections at joint B of the truss shown using the virtual…

A: Vertical Load = 100 kN Horizontal load = 50 kNArea = 1000 mm2E = 70 GPa or 70000 MPa

Q: Define Field Equipment.

A: Equipment refers to any item which can used for a serving a particular purpose in a operation or…

Q: Determine the bending stress along the x-axis of the W section. Determine the bending stress along…

A:

Q: Write equations for the shearing force and bending moment at any point in the beam and plot the…

A:

Q: If the irrigation efficiency is 80%, conveyance losses are 20% and the actual depth of the watering…

A: Irrigation efficiency-To Find-The depth of water required at the canal outlet (D).

Q: From a borrow material having 150000 m³ of volume and void ratio of 1.2, how many cubic meters of…

A:

Q: a) A polygon traverse has the following coordinates shown below. Calculate the area within the…

A: The area of a closed non-crossing plane polygon can be computed from the coordinates of the polygon…

Q: Water flows uniformly in a finished concrete rectangular channel (n = 0.02) with a bottom width of…

A: 1. bottom width of the channel = 0.85 m2. Flow depth in the channel = 0.4 m3. bottom slope of the…

Q: Sieve analysis was performed on a 1.565 lb dry soil sample "SAND 1", and the following data was…

A: sieve(in)diameter(mm)mass of sieve(lb) m1mass of sieve+retained soil(lb) m2mass retained(m2-m1)%…

Q: A traverse is closed if: O Sum of departures is zero O Sum of angles is zero FO Sum of latitudes and…

A: The latitude of a line is the the vertical component of the line that represents the north-south…

Q: 3. Water towers are often used to maintain city water pressure. In many locations, the static…

A: Given Data: Static Pressure = 65psi To find height of liquid in water=?

Q: An interior angle traverse with 4-sides was performed. The interior angles in a traverse are given…

A: As interior angle is given,  Need to find bearing of each line of traverse. Concept of same angle in…

Q: Design a diamond crossing between two BG tracks crossing each at an angle of 1 in 10. Show…

A:

Q: For the truss shown, determine the stress in members DC and DG. The area of each member is 800 sq.…

A: Given data: Area of each member is 800 mm2.

Q: 4. A closed traverse has the following data: Line Departure 37.39 Latitude DPD 2A АВ 1455.23 ВС…

A:

Q: The cable is subjected to the uniform loading shown below. Determine the following: a) Maximum…

A:

Q: The three hinged spandrel arch is subjected to the loading shown. Determine the following: a)…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub- parts for…

Q: - 25-mm-diameter In a standard tensile test a steel rod of 25-mm diameter is subjected to a tension…

A: