94444% 00962% 11702% 25000% 41892% ne of the Choices

Q: For a road with a distance = 3 km. Calculate (TMS) AND (SMS) for the following traffic. car Time…

A:

Q: A soil sample has an internal friction 30°, it is subjected to axial principal effective stresses…

A: The shear parameters of the soil can be calculated by different methods such as  Direct shear test…

Q: 1. Two platoons of cars are timed over a distance of 0.7 km. Their flows are recorded. The first…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Select the correct answer(s) to the statement, "disturbed soil samples cannot be used for" Select…

A: 1 .  here i chooses  the best option possible.

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A: E = 12 GPa Use virtual method to analyze the beam.

Q: Determine the following: (round off in 2 decimal places.) Moment at point D Maximum Moment Shear…

A: Given Data Determine 1. Moment at point-D.  2. Shear force at 5ft from point-D.  3. Moment at 3ft…

Q: 1. A soil has the following profile and a lateral stress coefficient at rest is 0.45. 0-4 G, = 2.75…

A: Given  K0 = 0.45  Take Unit weight of water  = 10Kn/m3 Water table is at 5m below the ground…

Q: 300 lb In the truss loaded and supported as shown, the following using the Method of Joints : 300,…

A:

Q: 2.20 A cylindrical soil specimen is properties were obtained: Sample diameter Sample length Wt.…

A:

Q: Q- In the layout of an MG track, the versine of a horizontal circular curve is measured over a 17 m…

A: Degree of curve = 2 Chord length = 17 m  To calculate: versine of curve.

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: Define Anchorage

A: The constructions made up of steel as a construction material requires connects of nuts and bolts to…

Q: 3 4.20 B A 4.0 m BAR WEIGHING 100 N IS REUTING ON A SMOOTH FLOOR AND AGAINST A MOOTH WALL AT POINTr…

A: To find the value of P

Q: From the following rocks prepare a list in order of their decreasing unconfined compressive…

A: The utmost compressive stress that a plastic specimen can sustain before rupturing or deforming by a…

Q: 1. Converging, diverging, transform 2. Pinatubo, Taal, Mayon 3. Sedimentary, igneous, metamorphic 4.…

A: 1.Types of plate boundaries 2.volcano in the Philippines 3.Types of rocks 4.trenches in the…

Q: The accident investigation is a legal requirement. It also aims to prevent a repetition of the same…

A: to find  ans of given question

Q: what are citc policy?

A: CITC is Communication and Information Technology Commission which regulates information and…

Q: Determine the minimum force P to prevent the 399-kg rod AB from sliding. The contact surface at B is…

A: Take moment about B:∑ MB=0NA3+fA4-mg42=0NA3+0.45NA4-399×9.8142=0NA=1630.9125N

Q: The particles created at the conclusion of the rapid mix step associated with the alum addition in…

A: settling velocity v=v=ρgd2(G-1)18μ where ρ density of waterg gravityd dia of particleG specific…

Q: forward tangent is -3.0%, and the location of the highest point elevation of the highest point is…

A:

Q: An essential 5-story facility structure is conceptualized with an intermediate reinforced concrete…

A:

Q: The equation of deformation is derived to be y = x² - xL for a beam shown in the figure. The…

A: Given: A beam shown in figure: The equation of deformation, y=x2-xL.

Q: 10.73 An engineer is making an estimate of hydroelectric power for a home owner. This owner has a…

A:

Q: In paragraph 5, what does the phrase "held our breath" suggest about the narrator and Josh? A They…

A: 1. C  They are waiting anxiously to see what mother will do next.

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: one-way slab to support a load

A: To design the slab for the given specifications

Q: 43. In groundwater flow, what are the units of head? a. length/time b. length c. length/time d.…

A:

Q: Define what is TRAVERSE or TRAVERSING in SURVEYTING?

A: Given data in question  Traverse    Traverse: The series of connected lines or preferably survey…

Q: tangent is -3.0%, and the location of the highes on of the highest point is 100 m. t is the Station…

A:

Q: The state of stress in a long dam is as shown in the figure, Determine oz in MPa? [E = 200 Gpa, u =…

A:

Q: 3. Which of the following is NOT a measure of forecasting errors? A. Mean absolute error (MAD) B.…

A: Explanation : Forecasting error is the discrepancy between actual and predicted demand numbers.…

Q: 8. Compute the AL and the Ad for each leg of the traverse shown below. Show the EL and the Ed as…

A: Lattitude and departure signs :  N-E : Both positive  S-E : Lattitude negative Departure positive…

Q: P₁ 3 m E B P₂ 3 m- D 4 m

A: Given TrussLoadsTo find out Zero force members

Q: Draw the projections of a regular hexagon of 20 mm side, having one of its sides in the H.P. and…

A: Regular hexagon of side 20 mm Inclination to Vertical plane = 45 degree.One side is at horizontal…

Q: The ratio of the upstream depth to downstream depth in a hydraulic jump for a rectangular,…

A:

Q: kN M = kN - m

A:

Q: For an undisturbed sample: given that Void ratio = 0.78 Water content 12% Specific gravity of solids…

A: Given: The void ratio is 0.78. The water content is 12%. The specific gravity of solids is 2.68.

Q: A composite beam is under external loads as shown below. a) Draw the internal shear force and…

A:

Q: Ca'cu'ate damping con" ciont c' a v y da dS 4g undergong resonant amplituden of 1.2 m wh a pndc03 s,…

A: Given, Mass=4kg Amplitude=1.2m Period=0.3s Force=270N

Q: Water 2. In this system, d = 6 in., D = 6 ft, and =z2 = 12 ft. The water in the system is 13 cfs.…

A: d = 6 in or 0.5 ftD = 12 in or 1 ft

Errors in surveying

An error in surveying is defined as the difference between two or more values of an identical quantity. However, the estimates are never accurate and there will always be a degree of variability regardless of the research tool or method used. These differences are known as errors that need to be reduced or eliminated to maintain certain levels of accuracy. Even if you carefully follow the prescribed test procedures, the considerations may contain errors.