The 9-m boom AB is acted upon by the 5.7 kN force as shown in figure. Determine the tension in cable BC. 4 m D. 2.5 m 2 m 1.8 m 4.5 m 5.7 khl 4.5 m-

Q: Explain grid leveling.

A: LevelingLeveling is the method or procedure to determine the relative altitude of any point on the…

Q: Define PDOP?

A: PDOP ( Position dilution of precision) It describes the error caused by the relative position of the…

Q: Define Eccentricity,

A: Eccentricity is a term is used in the loading condition of the engineering. for example, the load on…

Q: Where should the Drawings of clarification that contain supplemental information be kept and why?

A: The clarification drawings containing supplementary information is often needed in any construction…

Q: Define Bearings?

A: Bearing: It is defined as the angle which is measured between the reference meridian and the survey…

Q: Define earth work

A: The engineering work that is created by moving and/or processing unformed rock or large amounts of…

Q: Design a typical layout model for a Water Supply Scheme

A: Brief Concept- Water Supply Scheme- It is the set up of different units for the treatment of water…

Q: Define the Design working life ?

A: Design Life The design life (or design administration life) of a structure, other construction or…

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: Who keeps the design or site information in their possession?

A: The life cycle of the project can be defined as a mechanism by which a project is carried out from…

Q: create (P,L,E,A,N,U,G) 2D drawing using lines, circles, curves,etc

A: Here is your drawing

Q: Give a brief description: a. Measurement of Horizontal Distances b. Omitted Measurements c.…

A: Any plane which contains horizontal line and perpendicular  to the vertical direction is called as…

Q: Compute total indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2=6 Number of member attach at hinge joint…

Q: Define scale factor?

A: The size by which the shape is reduced is called as its scale factor. It is used when we need to…

Q: List the different meridians are used to specify directions?

A: The direction of a survey line can be defined in two ways: Relative to each other  Relative to some…

Q: Define Persistent design situation ?

A: A design situation is context where the design intervention will be applied to bring the beneficial…

Q: What is the most important thing to ensure when it comes to layouting?

A: Civil surveying is a type of engineering that includes analysing and documenting information about a…

Q: actors that cause hardness along with a bibliography

A: The water hardness may be simply defined as the amount of dissolved calcium and magnesium in the…

Q: CAD system to generate the final schematic

A: Computer aided design is the technology of designing,analyzing and modifying a structure before and…

Q: Give a detailed explanation and steps of the methodology of lot area sketch plan preparation.

A: The methodology for preparing a lot area sketch plan typically includes the following steps:…

Q: Define Spencer Charts.

A: Spencer defines the factor of safety as the available shear strength quotient divided by mobilized…

Q: What are the original field notes?

A: Original field notes are defined as the quality notes that are used by the researcher, surveyor, or…

Q: Define Soil conditions.

A: Soil condition:

Q: List the only tools needed for producing FREEHAND sketches

A: The only tools needed for producing FREEHAND sketches are listed in the following steps.

Q: Q#4: Define Baseline, Main survey line, check line and tie line?

A: - Baseline, main survey line, check line and tie lines are mostly used in triangulation surveying to…

Q: What is the difference between primary standards  and secondary standards in AAQS?

A: Primary standards:These standards for the air pollution control considered the public health…

Q: How many studs are require for the exterior wall on the main floor if there are two doors and 6…

A: Hi! Thank you for the question As per the honor code, We’ll answer the second and third question…

Q: D#2: Write different uses of Surveying?

A:

Q: How to create border with title box in autocad 2024

A: Steps to create:Border with title box in autocad 2024.

Q: m, tf = 12.80 mm and tw = 7.7 mm. The section is acted by a tensile force and attached to onnectors…

A:

Q: What is the arch dam?

A: Arch dam: It is a curved concrete dam, convex upstream and resists force acting upon it mainly by…

Q: Discuss MINIMUM COVER REQUIREMENTS AND STANDARD DIMENSIONS

A: Throughout reinforced concrete, the concrete cover is indeed the shortest route between the layer of…

Q: step by step procedure on doing this lab report (drawing/illustration) open compass traverse

A: Brief concept- Open compass traverse- A compass traverse is a technique for adding detail to a…

Q: What is an Elevatio Plan? Give its types as well. How do you draft floor & Elevation plans?

A:

Q: Define the terms Streamlines, Streaklines, Stream tube?

A: Streamlines Streamlines are a family of curves that are outright tangent to the velocity vector of…

Q: Why should a number 2 pencil not be used in field notekeeping?

A: Field notes are handwritten documentation of fieldwork completed at the time. Field notes should be…

Q: Define hydrogeology.

A: Hydrogeology:

Q: Please Help me make a layout plan for the construction site for a housing project.

A: The layout plan includes the details of floor such description and size of bedroom, kitchen, living…