Answered: If there were no forces being applied…

If there were no forces being applied to knots E and F, would there be any bars with a null internal force? Please justify your answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Problem 2: A flat plate, shown below, with a fillet radius of 0.1875 in. is subjected to an axial tension force of 1000 lbs on the right side. The plate is fixed on the left side. The dimension of the plate is given in the figure below and the thickness of the plate is 0.25 in. Note that all dimensions are in inches. It will be faster to model this in Creo Parametric Or Solid Works and then save it as a step file. Material is Structural Steel, same used in the tutorial (RECTANGULAR PLATE WITH CIRCULAR HOLE SUBJECTED TO TENSILE LOADING). 22500 2.25 4.0000 4.00 H PRT_CSYS DEF 0.1875 VPRT CSYS DEF R. 1875 f*f* R₁ 11 10.00 10.0000 3.0000 0.7500 3.0000 -0.7500 1.5000 $ 1.50
(a) Using the Force Method of Analysis, draw the shear force and bending moment diagram for Figure Q1. Assume A and C are rollers and B is pinned. EI is constant.
R2
A frame structure is shown in the following Figure. Members ABC and BD are pin jointed to supports at A and D, respectively. An external load 4kN is applied vertically at point C. Find the magnitude of the force in member BD? (Note, the member BD is a two-force body) O O O O O 4 kN Don't Know 24 kN 16 kN 4m 8 kN B 4m 4kN
Find forces in members BC, CF, FE
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.29 mm the values of elastic modulus for steel is 217 MPa. Take H1 = 4 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 7 x 7 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
Rods ABC and CDE have been welded at point C as shown in Figure Q1 (c). Both rods ABC and CDE are supported by cables at B and D respectively. At point A, the rod ABC is supported using a rough surface. Block M3 is attached using cable at E. Taking into consideration of Newton's third law, draw the Free Body Diagram (FBD) for the rod ABC and CDE Z* M₂ M1 F CG M3
Q7 For the bracket shown in the figure: The moment of the force (1000N) about pin A is.... > The moment of the force (1000N) about pin B is.. > The moment of the force (1000N) about pin C is..... -600mm 2 A 1000 N 500mm 200mm 240 N.m CCW, 562 N.m CCW, 1099 N.m CCW 200 N.m CW, 468 N.m CW, 915 N.m CW O 562 N.m CW, 1099 N.m CW, 240 N.m CW O 468 N.m CW, 915 N.m CW, 200 N.m CW O
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.66 mm the values of elastic modulus for steel is 207 MPa. Take H1 = 4 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 7 x 7 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = (in N) ii) Stress-induced in the top bar = (in N/mm^2) iii) Stress-induced in the bottom bar = (in N/mm^2)
The uniform door shown weighs 525 N and 2.50 m high and 4.00 m long. It is hanging from two hinges 2.00 m apart and 0.250 m from the top and bottom of the door (hinges C and D). Cable AB is connected to the door as shown to relieve the strain on hinge C. The tension in cable AB is increased until the horizontal force at hinge C is zero. (a) Find the tension in cable AB. (b) Find the magnitude of the horizontal component of force at hinge D. (c) Find the combined vertical force exerted by hinges C and D A 250 B „0.250m. 2.00 m 2.50 D 0.250m 4.00 m
Calculate the forces arising on A, B and D pins with the effect of 500N horizontal force in the frame system shown in the figure.
A steel panel is subjected to a compressive loading in order to improve the panel stiffness and to increase its buckling strength. It is swaged with the swage depth of 13 mm and swage angle of 60.07°. Its profile is as shown in Fig.Q2. Typical dimensions are shown in the figure and the thickness of the panel is 0.8 mm. The effective length of the panel is 750 mm. The relevant properties are: Modulus of elasticity Yield stress 200 GN/m? 240 MN/m? . Assuming that the buckling stress coefficient for a panel simply supported on both sides is 3.62 and that the post buckling relationship for the panel is Oy = 0.40, +0.60, where oav = average panel stress, o, = edge stress in panel and o = panel buckling stress, determine (a) the load/swage pitch at which initial buckling of the panel will ccur, (b) the instability load per swage pitch. (13 Discuss the effects upon the compressive strength of the panel of: (c) i) Varying the swage width; ii) Varying the swage depth 150 13 150 All dimensions…