If the weaving configuration below has four lanes and 2000 feet between the ramps, propose the improvements needed to reach an overall level of service of C. Assume a PHF of 0.92, 10% trucks, FFS of 65 mph, lane capacity under ideal conditions of 2,350 pcph and 0.8 interchanges per mile. VFR 1200 VPH = VFF 3000 VPH = VRR = 2300 VPH VRF 1000 VPH

If the weaving configuration below has four lanes and 2000 feet between the ramps, propose the improvements needed to reach an overall level of service of C. Assume a PHF of 0.92, 10% trucks, FFS of 65 mph, lane capacity under ideal conditions of 2,350 pcph and 0.8 interchanges per mile. VFR 1200 VPH = VFF 3000 VPH = VRR = 2300 VPH VRF 1000 VPH

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: An existing urban freeway with 4 lanes in each direction has the following characteristics. Traffic…

A: Traffic volume, V = 7110 veh/hr PHF = 0.93Lane width = 11 ftShoulder width = 6 ft

Q: Determine the level of service (LOS) on a Class I two-lane highway segment with rolling terrain and…

A: Step 1

Q: An undivided multilane highway segment has two 11-ft lanes in the eastbound direction with no…

A: The given data is shown below: Width=11ftSpeed limit=55 mi/hAccess points=40Distance=1.25…

Q: A freeway is being designed to carry a heavy volume of 5000 veh / h on a regular weekday in rolling…

A: Given data:- The freeway is designed to carry a heavy volume of, 5000 veh/h The given PHF is, 0.9…

Q: An existing urban freeway in rolling terrain is to be analyzed to determine LOS using the following…

A: Base FFS=70 mph.Number of lanes in each direction is N = 3.Peak hour volume is V = 3300…

Q: A four-lane urban freeway segment has a peak demand volume of 3,500 vehicles per hour for the two…

A: Freeway:Freeway is a roadway without any signals or intersections. A freeway does not have any…

Q: A four-lane basic freeway segment on level terrain is being redesigned. The current roadway has 12…

A: Given:- Current roadway: 4 lanes, each 12 ft wide, with 4 ft shoulders- Proposed roadway: 6 lanes,…

Q: An existing urban freeway with 4 lanes in each direction has the following characteristics. Traffic…

A: Traffic volume, V = 7110 veh/hr PHF = 0.93Lane width = 11 ftShoulder width = 6 ft

Q: A six-lane freeway (three lanes in each direction has regular weekday users and currently operat at…

A: Given:- peak hour factor=0.90 wide=11ft right side shoulder=4ft wide To find:- hourly volume

Q: A six-lane freeway (three lanes in each direction) in mountainous terrain has 10-ft lanes and…

A: We will solve this question in step no. 2

Q: A rural collector highway located in mountainous terrain is designed to carry a design volume of…

A: Given, This question Is related to Highway & Transportation Engineering. Our aim is to answer…

Q: An eight-lane freeway section is designed to have a lane width of 12 ft, right-side shoulder width…

A: Given; Lane width = 12 ft. Right-side shoulder width = 3 ft. and 3 ramps over a 2- mile- long…

Q: Q1 (A): Name and draw an interchange that contains one-way diagonal ramps in each quadrant and with…

A: 1)(A)(B)

Q: A segment of rural freeway is being designed for a FFS of 65 mph using 11 ft lanes in a mountainous…

Q: A new basic freeway segment will have 3 lanes in each direction. The left and center lane each has a…

A: Given : Basic freeway segment with 3 lanes in each direction. N = 3 Left and center lane each has a…

Q: Problem 2. Consider a freeway section with three lanes in each direction and with a length of 1.25mi…

A: First condition-Without Bus Removal: The peak hour volume is V=3800 veh/h. The total vehicles are,…

Q: What should be the design minimum acceleration lane length for a flat parallel-type entrance…

A: GIVEN- The design speed of a highway (u)=45mph The design speed of a highway (u)=20.1168m/sec The…

Q: A class III two lane highway in rolling terrain services a small built-up area. It has a base free…

Q: A segment of rural freeway is being designed for a FFS of 65 mph using 11 ft lanes in a mountainous…

A: The given data is shown below: FFS=65mphLanes=11ftLateral clearance=1 ftDesign flow rate=2400…

Q: A four-lane rural freeway segment has a 510 m grade length of 2% upgrade followed by a 630 m grade…

A: No of lane in both direction = 4

Question

If the weaving configuration below has four lanes and 2000 feet between the ramps, propose
the improvements needed to reach an overall level of service of C. Assume a PHF of 0.92, 10%
trucks, FFS of 65 mph, lane capacity under ideal conditions of 2,350 pcph and 0.8 interchanges
per mile.
VFR 1200 VPH
=
VFF 3000 VPH
=
VRR = 2300 VPH
VRF 1000 VPH

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

VIEW

Step 2: Solution:

VIEW

Step 3: Volume:

VIEW

Step 4: Weaving segment:

VIEW

Step 5: Speed:

VIEW

Solution

VIEW

Step by step

Solved in 6 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 2 southbound lanes of a four-lane (i.e. 2 lanes each direction) urban freeway are 12 ft wide. There is at least 6 ft of lateral clearance on the right side of the outer/right lane. There are two ramps within the influence area (i.e. within 3 miles upstream and 3 miles downstream of the center of the segment. What is the estimated FFS (mph)? Provide the answer to the nearest tenths. Response Feedback: The BFFS of 75.4 mph is reduced by 1.28 mph to account for the presence of ramps.
A long segment of suburban freeway is to be designed on level terrain. The level segment, however, is followed by a 4.5% grade, 2.0 miles in length. If the DDHV is 2,500 vehicles per hour with 15% trucks (standard mix), how many lanes will be needed on the (A.) Upgrade, (B.) Downgrade, (C.) Level terrain segment to provide for level of service C? Lane widths and lateral clearances may be assumed to be 12 feet and 6 feet, respectively. Ramp density is expected to be 1.0 ramps per mile. The PHF is 0.92. Good weather, no incidents, no work zones, and regular users of the facility may be assumed.
Answer fast
Eight lane urban freeway is on mountainous terrain with lane width of 12 ft, right shoulder lateral clearance of 4 ft, and 12 ramps over the 6-mi analysis segment. The traffic stream consists of familiar road users. Peak hour volume for a directional weekday of 5200 vehicles is observed with 500 vehicles arriving in the most congested 15-min period. If the traffic stream has 10% large trucks and 12% buses and 10% recreational vehicles, determine the heavy vehicle adjustment factor. Round your answer to 3 decimal places. Exclude the unit in the answer box.
The 2 southbound lanes of a four-lane (i.e. 2 lanes each direction) urban freeway are 12 ft wide. There is at least 6 ft of lateral clearance on the right side of the outer/right lane. There are two ramps within the influence area (i.e. within 3 miles upstream and 3 miles downstream of the center of the segment. What is the estimated FFS (mph)? Provide the answer to the nearest tenths.
A 5% upgrade on a six-lane freeway (three lanes in each direction) is 1.25 mi long. On this segment of freeway, there is 3% SUTS and 7% TTs, and the peak-hour factor is 0.90. The lanes are 12 ft wide, there are no lateral obstructions within 6 ft of the roadway, and the total ramp density is 1.0 ramps per mile. What is the maximum directional peak-hour volume that can be accommodated without exceeding LOS C operating conditions in veh/h? Round of your answer to whole number. Blank 1
A two-lane rural highway carries a peak hour volume of 465 (vph) and has the following characteristics: Roadway: 60mph design; 11 foot lanes, 2 foot shoulders; rolling terrain; 60% no-passing zones; length = 3 miles. Traffic: 70/30 directional split; 4% trucks; 2 percent recreational vehicles; 1 percent buses; PHF = 0.95 a) What Level of Service will the highway operate under during peak periods? b) What is the capacity of the highway? Explain why this is less than 2,800 (vph)?
How many diverging conflicts are present at a 4-leg intersection where each leg is a single lane approach, as shown above? Response Feedback: NBTH with NBLT, NBTH with NBRT EBTH with EBLT, EBTH with EBRT SBTH with SBLT, SBTH with SBRT WBTH with WBLT, WBTH with WBRT
A new section of a freeway is to be designed with a free-flow-speed of 65 mph along of 0.75 mile on 5% upgrade. The expected traffic volume is 4200 v/hr. The traffic composition is 15% trucks, 5% recreational vehicles, and 10% buses. The peak hourly factor is 0.9, the unfamiliar driver factor is 0.95. If the design requirement is to target a level of service (B), how many lanes must be provided to satisfy the design requirement?
A rail transit system has prescribed the following factors:1. Peak hour demand = 30000 passengers/hr2. Minimum required speed = 55 ft/sec3. Deceleration = 3 ft/sec24. Safety factor = 1.455. Vehicle length = 80 ft6. Allowable vehicle capacity = 150 pass/veh7. Guideway utilization factor = 0.838. Minimum headway = 110 secHow many cars should the train consist of to provide adequate passenger capacity?
An existing four-lane freeway in rural area is with the following :information Lane width 3.5m, 0.9m lateral clearance, 1800 veh/hr peak hour volume, PHF=0.9, interchange density =0.90, 5% trucks, 5% buses and the road is within a mountainous terrain. Then based on the HCM procedure, the service flow rate (pc/h/In) is
An eight-lane freeway has a basic freeway segment on rolling terrain. It has 12-ft lanes with a 4-ft right shoulder. There are seven ramps within the six-mile segment. The directional peak traffic volume is 5200 veh/h with 6% trucks and 2% buses. The PHF is 0.90. Calculate the FFS, vp , and determine the LOS