If the tension in the gantry-crane hoisting cable is T = 28 kN, determine the unit vector n in the direction of T and use n to determine the scalar components of T. Point B is located at the center of the container top. Assume a = 13 m, b = 8 m, c = 2 m, d = 6 m, e = 10 m, f = 5 m, and h = 18 m.

If the tension in the gantry-crane hoisting cable is T = 28 kN, determine the unit vector n in the direction of T and use n to determine the scalar components of T. Point B is located at the center of the container top. Assume a = 13 m, b = 8 m, c = 2 m, d = 6 m, e = 10 m, f = 5 m, and h = 18 m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rigid pipe is subject to the following loads. Neglecting the weight of the pipe, determine the moment at O. SOLVE THE FF Vector component form of 50-lb force (ANSWER: 25.000i +0j -43.30k lb) Magnitude of the resultant force (ANSWER: 78.10 lb) Position vector of the 50-lb force from point O to its point of application on the pipe. (ANSWER: -15i -10j +12k inch) Moment at point O, in vector component form. (ANSWER: 1153.01i -829.52j +250.00k lb-in)
The line of action of the 2000-lb force runs through the points A and B as shown in the figure. Determine the x and y scalar components of F. y, m B (7, 6) = 2000 lb A (-10, -4) I Answers: Fx= Fy= || F - x, m lb lb
The member is supported by a square rod which fits loosely through the smooth square hole of the attached collar at AA and by a roller at B. The member is subjected to the forces F1 = 350 N , F2 = 450 N , and F3 = 600 N . Determine the normal reaction force of roller at B. Determine the components of the reaction force of the support at A using scalar notation. Determine the components of moment of the reaction at A using scalar notation.
7
Calculate the moment about point O of the 200-lb force that lies in the X-Y plane shown below. Solve the force into rectangular components at point M. X(-)- Fy Y(+) Y(-) 2'-0" M F 3'-0" 30° F = 200 lb X(+)
The horizontal force F = -Fi acting on the handle of the wrench produces a component of the moment along the OA axis (z axis) of the pipe assembly of M, = {4.4 k}N•m. Both the wrench and the pipe assembly, OABC, lie in the y-z plane. Suggestion: Use a scalar analysis. y-z (Figure 1) Part A Determine the magnitude of the force F. Express your answer to three significant figures and include the appropriate units. HA F = Value Units Figure < 1 of 1 Submit Request Answer Provide Feedback 0.8 m 0.2 m 135 0.6 m
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. - A = 15°1 A 250 mm lllllll 900 mm k = 2.6 kN/m OB = 30° B G 200 mm
The tension in cable CD is T = 545 lb. Consider the force which this cable exerts on point C and determine its moment about point O. Assume a = 14 ft, b = 6 ft, c = 9 ft, d = 12 ft, e = 15 ft. d A T a Answer: Mo = ( i i+ i j+ i k) Ib-ft
4-151. Currently eighty-five percent of all neck injuries are caused by rear-end car collisions. To alleviate this problem, an automobile seat restraint has been developed that provides additional pressure contact with the cranium. During dynamic tests the distribution of load on the cranium has been plotted and shown to be parabolic. Determine the equivalent resultant force and its location, measured from point A. 12 lb/ft 0.5 ft w 12(1 + 2x) Ib/ft 18 lb/ft
1
show solutions pls thank you
5