If the eyebolt is made of a material having a yield stress of OY= 275 MPa and the factor of safety F.S. = 1.45 against yielding, draw the appropriate FBD's and determine a. allowable stress in the eyebolt. b. minimum required diameter dof its shank.

Q: Maxinam allowable stress for steel -140 MPa Maxinnum allowable stress for ahıminuum = 90 MPa Maxinun…

A: Given:- Maximum allowable stress for steel = 140 MPa Maximum allowable stress for aluminum = 90 MPa…

Q: A Solid Steel bar of diameter 60mm and length 50mm is placed inside an aluminum cylinder of Inside…

A: The given data is: ES=200 GPa     =2×105 N/mm2 EAl=70 GPa      =7×104 N/mm2 Ls=350 mm…

Q: The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was…

A:

Q: The following steel member is connected to the gusset plate via two longitudinal welds. The width of…

A: Width of the member = 58 mm Length of the weld = 87 mm Yield Stress fy = 300 MPa Ultimate Stress fu…

Q: A Sandwich block is comprised of brass in the centre with two aluminium plates attached to either…

A:

Q: The member shown in the right side consists of the steel rod AB that is screwed into the end of the…

A:

Q: The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a…

A: Figure is as shown

Q: GIVEN: Solid aluminum bar shown: 4 in. by 4 in. E = 10 x 10° psi oy = 36 ksi 4000 & 200016 4000 16 B…

A: A) Load in each section of bar PAB = 4000 lb ( T )  PBC = 4000 - 2000 = 2000 lb ( T ) PCD = 4000 -…

Q: The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress…

A: The given data is as follows: Size of square block=200 mmCompressive load=300 kN

Q: 1.(e) The state of plane stress shown occurs at a critical point of a steel machine component. As a…

A:

Q: 1.12 A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90…

A:

Q: A copper bar is of uniform cross-section and is rigidly attached to the walls as shown. The rod is…

A:

Q: If the eyebolt is made of a material having a yield stress of Y = 275 MPa and the factor of safety…

A: The given data is: Yield stress (σy) = 275 MPa FS = 1.45

Q: Bronze Aluminum Steel A=400 mm? A= 600 mm? A=300 mm? 2P ЗР 4P -3 m -5 m 4 m Three round bars welded…

A:

Q: A brass sleeve S is fitted over a steel bolt B, and the nut is tightened until it is just snug. The…

A:

Q: 12 A plate of 150 mm width and 20 mm thick is welded to another plate by fillet weld as shown in…

A:

Q: 8 ksi, øy = -4 ks The normal stresses at a point in a steel member are ox 10 ksi. Using E = 29 × 10³…

A: Given data in question  Stresses Elasticity modulus  Poissons ratio To find out  Normal strains

Q: The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of…

A:

Q: The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find the…

A:

Q: 2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions…

A:

Q: specimen of steel 20mm likameter guage length or 20mm s destruchon. It has an extenscon Wth a tested…

A: given: inital dia (d0)=20mmgauge length (l0)=200mmδl1=0.25mmδtotal=56mmdia neck (dneck)=15mmw1=80…

Q: Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. 3 m…

A:

Q: The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this 640…

A: Given : Diameter of steel bolt = 10 mm Outer diameter of sleeve = 20 mm Inner diameter = 10 mm Yield…

Q: A The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find…

A:

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the…

A:

Q: A brass sleeve S is fitted over a steel bolt B, and the nut is tightened until it is just snug. The…

A: To determine the rise in temperature that would cause a given compressive stress in the brass sleeve…

Q: Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the…

A:

Q: IWOO steel plates are connected by a pair of spiice plates with eight bolts as shown. The ultimate…

A:

Q: The state of plane stress shown occurs at a critical point of a steel machine component. As a result…

A:

Q: When designing a structural member, which of the following statements is FALSE?   A. The allowable…

A: Asked 1. False statement in designing a structural member. 2. Safety factor. 3. L = 1000mm, d =…

Q: The tension member shown in figure below consists of steel pipe,A which has an outside diameter of…

A: We have to find the bearing stress

Q: Required information Consider the loading shown. The allowable normal stress for the steel used is…

A: Allowable normal stress, simply supported beam with uniformly distributed load is .The load is…

Q: O Compute the maximum value of P that will not exceed a stress of bronze of 100 MPa. Bronze Aluminum…

A:

Q: What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a…

A:

Q: The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the…

A: T1 = 30oCT2 = 180oCT = 180 - 30 = 150oC0.1 mm gap between rod and member AE