if the cross-section shown in the figure has shear stress of 300psi at point P( located 0.25 in below the top line), find the shear force on the cross-section.

Q: A cross section of the leading edge of an airplane wing is shown in the figure. The enclosed area is…

A: Given : A = 82 in2 T = 100 kip.in

Q: The dimensions of the beam with the cross-section are given as b, a, t as in the figure on the…

A: Given data The dimensions of the beam with the cross-section are given as b, a, t as in the figure…

Q: A solid shaft is subjected to two shear forces and a torque as shown in the figure. Assume that the…

A: Given data:-  L=205 mm Vy= 9kN Vz =19kN T= 499 N-m d =61 mm

Q: per the attached figure: if the applied shear force V = 14 kip, determine the maximum shear stress…

A: For the given block the neutral axis from top is,

Q: A thin plate is composed of two CST elements, as shown in the figure below. The plate is subjected…

A: I have attached the image below Explanation:

Q: torque that will cause a maximum shear stress of 10 000 psi. Use G = 4x 106 psi for aluminum. e-4…

A: Solnn:- in a given figure  Sear stress=10000 psi G= 4×10^6 psi Now, enclosed area Am= π\2  ×  r^2 +…

Q: A section is under the effect of M (kNm) bending moment which makes 6° with the positive +z axis as…

A:

Q: 4. The general stress element is loaded such that ty = 25 MPa. Using Mohr's circle, find out the…

A:

Q: Find the maximum shear stress for the stress case given in the figure.

A: Given Data The stress acting in x direction is: σx=100 MPa The stress acting in y direction is:…

Q: Mohr's circle for an element is shown below. If each grid is 15 MPa then the maximum shear stress…

A: Mohr's circle is a two-dimensional graphical depiction of the Cauchy stress tensor transformation…

Q: A simply supported beam (i.e., with a pin support at point A and a roller support at point D) is…

A:

Q: Qr) Find the stress distribution at the section ABCD for the block shown in the figure. Sketch the…

A:

Q: Calculate the principal normal stresses and their directions, the maximum shear stresses and the…

A:

Q: For the system shown in the figure, find the maximum internal shear force in kN. Hint: you will need…

A:

Q: A steel wide-flange beam has the dimensions as shown in the figure below. If it is subjected to…

A: According to the given information we have shear force of v = 86 Kn firstly for the moment of…

Q: In the figure, the steel shaft with a diameter of 36 mm is 240 mm diameter pulley. Belts also formed…

A:

Q: In the figure, both ends of the rectangular plate are under the effect of a force p = 150kN. What is…

A:

Q: Find the normal and shear stresses at points H and K, since F= 15 kN in the loading condition shown…

A:

Q: For the I section shown in figure. If the section is subjected to a shear force of 120 kN, determine…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Şekildeki kenar uzunluğu b= 160 mm olan kare kesit üzerine gelen M=170 kN.m'lik momentin yönünün z…

A: We need to find out of A,B,D & E which will be subjected to maximum compressive stress

Q: 40Mpa with σx = 70MPa σy = 40MPa Calculate the in-plane maximum shear stresses and angles using both…

A:

Q: Calculate non-zero stress components (normal and shear) at points A, B and C. Point C is located at…

A: Given: The length of the bar→L=100 mm=0.1 m Diameter of the bar→d=15 mm=0.015 m At point A: Because…

Q: maximum shear stress

A:

Q: Beam cross section is shown in Figure Q3 and given the second moment of area is I= 20.85 x 106 mm*.…

A: Find the shear stress at point M, N, O, P and draw stress distribution over the cross section

Q: Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw…

A:

Q: In the figure, the boards are connected by nails to form a beam. A shear force of V= 70 kN acts on…

A: The shear force applied is The dimension of plate is The shear strength of each nail is

Q: For the framc shown in the figure, Find the normal and shear stresses based on the following…

A: Given: The diameter of the pin at A, d = 10 mm The diameter of the pin at C, D = 15 mm

Q: For the beam shown in the figure: Determine the normal and shear stress at a point located at 4.5 ft…

A:

Q: If the cross section shown in the figure has a shear stress of 300 Psi at point P (located 0.25 in…

A: Given data:-  Shear stress at point P(below 0.25 in from top fiber) is 300 psi. Find the shear force…

Q: Q: Shear force acting on a section of a bea is 60 kn. The Section of the beam is of T- Sha of…

A: V = 60 KN T shape Dimensions = (120×120×20) mm

Q: Find the stresses in each section and total change in length of the bar as shown in figure.  The bar…

A: