If the Control Volume is initially a vacuum, the initial mass and energy of the system is zero Select one: O True O False Nozzle: Kinetic Energy; Turbine: Select one: O a. Pressure O b. Work c. Velocity O d. Heat

If the Control Volume is initially a vacuum, the initial mass and energy of the system is zero Select one: O True O False Nozzle: Kinetic Energy; Turbine: Select one: O a. Pressure O b. Work c. Velocity O d. Heat

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter23: Compressors

Section: Chapter Questions

Problem 9RQ: Describe the reciprocating compressor piston, rod, crank-shaft, valves, valve plate, head, shaft...

See similar textbooks

Similar questions

Q4: Why the stroke length of the racing cars' engines is always smaller than its bore diameter?
Q3) A compressor, requiring 90 kW is to run at about 250 r.p.m. The drive is by V-belts from an electric motor running at 750 r.p.m. The diameter of the pulley on the compressor shaft must not be greater than 1 meter while the centre distance between the pulleys is limited to 1.75 meter. The belt speed should not exceed 1600 m/mi. Determine the number of V-belts required to transmit the power if each belt has a cross-sectional area of 375 mm² density 1000 kg/m and an allowable tensile stress of 2,5 MPa. The groove angle of the pulley is 35°. The coefficient of friction between the belt and the pulley is 0.25.
Q3: A distillation column is separating acetone(more volatile component) from ethanol. As pictured, there are two feeds with flow rates F₁=100 mol/hr and F₂-200 mol/hr. Feed 1 has z₁-0.7 and is saturated liquid. Feed 2 has z2 0.4 and is a superheated vapor (q=-0.1) where approximately 1 mol of liquid will vaporize on feed stage for each 10 mol of feed. We desired xd-0.95 and xw-0.05. How many stages are needed to achieve this separation? Ln/Vn=0.64.
Thermodynamicccs
Q 1: For a particular gas system, the internal energy is given by : U = 2.5 PV + C , where P: Presure , V: volume and C : constant, the sysytem is taken into cycle shown in fig.(Q1) below with three Processes, Calculate Q & W if the pressure is given by P= 105+ 10° (v-0.02)² ? 0.5- 0.4E 0.3E A 0,2 A 001 002 003 V (m³) > Fig. (Q1) P (MPa)►
1.) A hand pump is used to inflate a bicycle tire to a gauge pressure of 70 psi. a) How much work must be done if each stroke of the pump is an adiabatic process and what is the final temperature of the gas? b) We inflate the tire in two steps: (i) an isobaric compression and (ii) an isochoric increase in temperature. Calculate the work done by gas/"us" and/or heat added/removed during the two steps! Is this a viable alternative to the adiabtic compression Explain! Atmospheric pressure is 1 atm, the air temperature is initially 25° C, and the volume of the air in the tire remains constant. Useful values: A bicycle tire is 26 in diameter and has a cross-sectional area of 2 in² [1 in = 2.54 cm]. 1 lb corresponds to a mass of 0.445 kg. c) For Take-Home only Solve the questions in a) and b) in terms of the initial pressure P₁ = P*, the final volume Vf = V* and the pressure ratio K = Pf/P*!
Identify what is the system in this problem and write the general energy balance equation (no need to solve) A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the specific delta H?
Q. Briefly describe the principle of corresponding states
1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle') Turbine Steam generator Condenser Coling water Economiaer The power plant control room reports that the plant is operating continuously at the following peak load conditions: a. Power to pump = 300KW b. Rate of steam flow = 25 kg/s c. Cooling water temperature at condenser inlet = 13 C d. Cooling water temperature at condenser outlet = 34 C Additionally, the following measurements were made at various points in the piping connecting the power plant components Data Pressure Temp. Quality enthalpy Specific Velocity (kJ/kg) point (kPa) volume (m/s) (m3/kg) (C) (x) 1 6200 2 6100 43 5900 177 ---- 4. 5700 493 ----- 5 5500 482 ----- 6 103 0.94 183 7 96 43 -----
Q-1(c): Consider a case in which the air inside the pressurized cabin of a jet transport flying at some altitude of pressure, 0.9 atm and of temperature, 15°C. The total volume of air at any instant inside the cabin is 1800m3. If the air in the cabin is completely recirculated through the air conditioning system every 20 min, calculate the mass flow of air in kg/s through the system. I Answer:
pls correct this given this is my last attempt thanks
Answer the attached file