If the allowable bearing stress for the material under the supports at A and B is o, = 760 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 4 in. by 4 in. The reactions at the supports are vertical. Assumew= 650 lb/ft, a = 12 ft, and b = 6 ft.

If the allowable bearing stress for the material under the supports at A and B is o, = 760 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 4 in. by 4 in. The reactions at the supports are vertical. Assumew= 650 lb/ft, a = 12 ft, and b = 6 ft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,)low = 20ksi , and the allowable bearing stress between the pin and the bar is (0,)allow = 30ksi , determine the dimension w and t so that the gross area of the cross section is wt = 2in² and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the prjjected area whenj calculating the bearing stress.) t d w/2 w/2
If the allowable bearing stress for the material under the supports at A and B is ob = 720 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 3 in. by 3 in. The reactions at the supports are vertical. Assume w = 750 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax i b lb P
If the overhanging beam is made of wood having the allowable tensile and compressive stresses of 4Mpa and 5Mpa, determine the maximum concentrated force P that can be applied at the free end. Can you also please explain the calculation of centroid. I'm a bit confused of the values that I need to use. Thank you
determine the ractions ro the supports
Question 2 : The composite beam consists of a wood core and two plates of steel. If the allowable bend ng stress for the wood is (oaiow )y = 20MPa and for the s(o aienl =130MPA zilow determine the maximum moment that can be applied to the beam. E, =11GPA , E= 200GPA Take: A = 125 mm A mm B = 75 mm M 20 mm- B mm 20 mm Solution : E 200(10" E 1110° The width of steel must be increased to an equivalent width for wood: Page 1 18.182 W. mm
For the below assembly, if the gap between C and the rigid wall at D is initially 0.1 mm, determine the support reaction at poire A after the load (P-220 kN) is applied. The two parts of the assembly a made of A36 steel with E-200 GP -600 mm 50 mm B 600 mm 25 mm 0.1 mm
Provide the correct exponents and distances to make the singularity function given valid for the beam shown. VI = 8 kN, V2 = 8 kN, V3 = 200 mm, and V4 = 1100 mm. Determine the reaction forces at the supports. A v3 V37 (m) o The singularity functions are q = R1(x)ª – v1( – P)ª – v2(x – Q)ª + R2(x – R)ª - 2 - V = R1 – v1(x – D)B – v2(x – E)B + R2(x – F)® (1) M = R1x – v1(x – G)° – v2(x – H)° + R2(x – (2) From the given singularity functions, the exponents are A = B = C= The distances are P= mm Q = mm R= mm D= mm E= mm F= mm G= mm H= mm mm Reactions force R = kN and reaction force R2 = kN
If the allowable bearing stress for the material under the supports at A and B is 0,730 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 3 in. by 3 in. The reactions at the supports are vertical. Assume w=550 lb/ft, a = 10 ft, and b = 5 ft. Answer: Pmax= b Ib
Determine the magnitude of the pin force at A. Assume W = 900 Ib, a = 5.8 ft, b = 3.9 ft, r = 9 in. B W Answer: A = i Ib
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joist are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is s allow = 1700 psi, determine the smallest height h so that the beam will support a load of P = 600 lb. Also, will the entire joist safely support the load? Neglect the stress concentration at the notch.
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
7.6 help Provide labeled free body diagram