A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown, determine the reactions at A and B. Take L=230mm, F1=60N, * F2=130 N,M=14 N.m F2 B 150 mm м FI 50 mm -225 mm-

Q: A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown,…

A: Forces acting in x directions are Ax+RBcos45=F1Ax+0.70RB=70⋯⋯⋯(1) Forces acting in y directions are…

Q: For the frame and loadings shown P=270 KN, and F=540

A:

Q: A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown,…

A: Given: The bracket is shown below:

Q: Determine the magnitude of the pin force at A. Assume W = 580 lb, a = 2.9 ft, b = 2.4 ft, r = 8 in.…

A:

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 184 lb, is…

A: There will be two reactions at thrust bearing and tension in the cable. Since Force F acts in single…

Q: If the roller A is replaced by a pin, determine the corresponding reactions at A and then Identify…

A:

Q: 2-1. The steel framework is used to support the reinforced stone concrete slab that is used for an…

A:

Q: The member is supported by a square rod which fits loosely through the smooth square hole of the…

A: Draw the free-body diagram.

Q: The frame shown is supported by a pin at A and a fixed support at D. There are internal hinges/pins…

A:

Q: A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown,…

A:

Q: The bar AB has a built-in support at A. An external force F=6kN is applied at B (8,0,0)m, towards to…

A:

Q: Determine the magnitude of the pin force at A.

A:

Q: Determine the magnitude of the pin force at A. Assume W = 690 lb, a = 2.8 ft, b = 2.1 ft, r = 8 in.…

A:

Q: A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown,…

A: First make a free body diagram as shown below,

Q: A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown,…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 525 lb, a = 3.1 ft, b = 2.4 ft, r = 7 in.…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 790 lb, a = 4.1 ft, b = 3.0 ft, r = 8 in.…

A:

Q: Find the reaction at A due to the uniform loading and the applied couple. The force reaction is…

A: From equilibrium; ΣFy = 0; RA = -2.5 * 2  RA = 5 kN

Q: A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown,…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 30…

A: Solution:

Q: Problem 3, The metal stud punch is subjected to a force of 120 N on the handle. Determine the…

A: P=120 N

Q: determine the reactions at A

A: Given: TO determine: The reaction at A and B

Q: Determine the magnitude of the pin force at A. Assume W = 695 lb, a = 4.7ft, b = 3.8 ft, r = 8 in. r…

A: Given that: W = 695 lb a = 4.7 ft b = 3.8 ft r = 8 in = 0.667 ft It is required to determine the…

Q: Determine the magnitude of the pin force at A. Assume W = 750 lb, a = 2.7 ft, b = 2.0 ft, r = 6 in.…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 670 lb, a = 5.2 ft, b = 3.5 ft, r = 7 in.…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 510 lb, a = 3.0 ft, b = 2.0 ft, r = 6 in.…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 615 lb, a = 3.2 ft, b = 2.3 ft, r = 9 in.

A:

Q: Determine the magnitude of the pin force at A. Assume W-850 lb. a 3.0 ft. b-2.2 ft, r = 7 in.

A: Given data:- W= 850 Ib a =3.0ft b =2.2 ft r =7in To find:-the magnitude of the pin force at A

Q: Find the reactions at D and B..Take F1=150 * ,N,F2=75 N, F3=200N, M-17 N.m 45-85mm - 75 mm M. D 125…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.