If R = 6 Q, what is the numerical value of v (in Volt) in the circuit below? 20 U6 +. 18 V 8Ω Vx | R 330

Q: A pulse width modulated signal is high (5 V) for 1 millisecond, low (0 V) for 3 milliseconds, high…

A:

Q: 7) Two conductors of the same length and material but of different cross-sectional area are…

A: Assume that  Length of conductor 1 =L Cross section area of conductor A =A1 Length of conductor 2=L…

Q: The maximum load current that can be drawn is 30 V 1.4 mA 2.5 mA 1.8 mA 2.3 mA 15 kQ2 ww V₂=9V R₂=0…

A: We need to find out the current through load and diode for given circuit .

Q: 8. Find the charge and current in an RLC circuit with R = 11 ohms, L (0.1 )H and C (0.01 + F, which…

A:

Q: Prepare truth table for the following Boolean function and also determine the complement of the…

A:

Q: E- Let S {S1, S2, S3, S4, S5, S6} , find out the entropy of S if !A= ('s)d P(s1) = 0.995 and P(s) =…

A:

Q: with a subtransient reactance of 0.1 pu, are connected through a line of reactance 0.1 pu on the…

A: The solution is given below

Q: Sub-Parts A,B and C, have been solved by a Bartleby expert earlier, and told me to post the question…

A: Solution (d)

Q: 4. What is the equivalent output of a circuit in dBm if it has an output of 10 watts? 5. If four…

A: here we need to convert power from watts to dBm

Q: A compound motor has 1200 turns on the shunt winding and 25 turns on the series winding, per pole.…

A:

Q: A shunt motor is connected to 230V line and running at 1000r/min. Armature current is 60A and total…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: A channel Capacity is 16Mbps for a signal bandwidth 4MHZ. Find: 1- Channel S/N Ratio 2- E/N. Ratio…

A: Given :   Rb = Bit rate   L = signal levels    n = number of bits    Rb = Bit rate    Rb = 24 Mbps .…

Q: Let Fla.b.c.d) Em(3,4,5,7,10,14) + d(1,6,15). Using a 4– to –1 multiplexer with no external gates,…

A: 4*1 MUX can be designed as

Q: I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards…

A: According to the question we need to design a wooden train that runs on wooden track.What's the…

Q: Good day! Please help me define LDA, ADD, SUB, OUT, and HALT in SAP - 1.

A: We have to define LDA, ADD, SUB, OUT, and HALT in SAP

Q: Is it required to use a PMMC instrument in an Instrument transformer based measurement system? a.…

A: Given:

Q: 3. Write an HDL design module, hw8_circuit, to describe the functionality of the circuit shown…

A: According to the question, for the given circuit as shown below We need to describe the…

Q: 5. A circuit-switch TDM-link uses 512-bit frames with 24 slots. a) How many circuits' are allocated…

A:

Q: x(t)=e*18t(u(t-8)-u(t-18)) h(t)=t(u(t-8)-u(t-18)) find y(t)=x(t)*h(t) using convolution integral.

A: For a linear time-invariant (LTI) system, the output y(t) is related to the input x(t) through…

Q: (a) Solve the total impedence and phase angle. (b) Write an expression for I(t). (c) Calculate the…

A:

Q: Q7) Using block diagram reduction technique find closed loop transfer function C(s) / R(s) shown in…

A:

Q: usal. (a) h[n] = (1/2)"u[n] (b) h[n] = (1/2)"u[n – 1] (c) h[n] = (1/2)m %3D %3D

A:

Q: Question 1 Analyze the latch circuit shown A. Derive next-state equation using Q as state variable…

A: Given

Q: Please leave a detailed explanation.

A:

Q: Decide on the required number of wind turbines needed. 2. In your own words, explain what the Betz…

A: Wind turbine require - minimum wind speed (generally 12-14 km/h) to begin turning and generate…

Q: Question (3):. (i) (ii) Which is the fourier transform of the given time signal? -T Alternative I)…

A:

Q: 8. Find the charge and current in an RLC circuit with R = 11 ohms, L (0.1 -) H and C (0.01 +) F,…

A:

Q: 16.4 The adjustable limiter in Fig. 16.11(a) has R₁ = 12 kn, RF = 70 kN, R₂ = 8 kN, R3 = 1 kN, R4 =…

A:

Q: Find the individual current and voltage drop across each resistors if C₁= 48 12, C₂=2512, and…

A: The required parameter can be calculated by using the nodal analysis and ohm's law. The node voltage…

Q: If the resistance of a circuit decreases while the voltage remains constant, what happens to the…

A: If the resistance of the circuit decreases while the voltage remains constant what happens to the…

Q: What is ampere circuital law?

A: This law gives the relation between the magnetic field and the current which created the magnetic…

Q: X = AB + CD + (A + B)(ACD + BE)

A: We have to draw the circuit of given function.

Q: Determine vC, il., and the energy stored in the capacitor and inductor in the circuit under de…

A: Apply source transformation 12 = 4ILIL = 3 A Voltage across 1 ohm resistance will be  V1 = 1×3V1= 3…

Q: why is it important to calculate the Percentage Voltage Regulation of an Electrical Equipment or…

A: According to the question we have to explain, why is it important to calculate the Percentage…