If my desired output rate is 75 units per hour, what is the efficiency of my setup? Aniwer to 20eemals

Q: , how do you add vectors using parallelogram method graphically

A: Vector can be a quantity that has some magnitude and have a specific direction. displacement,…

Q: Produce a 3D solid model of the Guard casing and test boss

A: Given Test boss Guard casing To find 3D solid model

Q: The input D rotates at 200 rpm clockwise viewed from the left with a torque of 40 Nm. The efficiency…

A: Given: Speed of input DIs=200 rpm Torqueτ=40 Nm Efficiency η=75%

Q: where are the graphs?

A: Given data in the related question: Maximum speed = vf = 183.58 mi/hr Distance travelled = 5 mi Time…

Q: 5. Use calculus to explain why the rotation velocity of a point on the perimeter of a wheel is the…

A: In this problem, it is asking for only part (5) so we will answer only part (5).

Q: Give all the location dimensions between the datum target points, B1 ,C1 and B2, C1. B1, C1 : X =…

A: Since, the bottom part of the drawing represents dimensions in X and Y direction while the upper…

Q: C 80±0.5 - 40 50±0.5 20 la be oxi odr wode wo B A.

A:

Q: You have been selected by an engineer for them to design their newest robotic prototype. As of this…

A: The first version of any machine, including robots, is called a prototype. Following the creation…

Q: 10) An automobile is driven by at 30kph for 12 min , then at 40 kph at 4 min and finally at 50kph at…

A: Given data: V1=30 kpht1=12 min=0.2 hourV2=40 kpht2=0.0667 hourV3=50 kpht3=0.1667 hour Need to…

Q: For the system given in the figure on the right-hand side, where the input is four-unit step i.e., r…

A: givenAs per the Bartleby policy I am solving Part a, b, c and d.

Q: A flange used to connect two pipes is shown in Figure Q3. Holes need to be drilled to fix it.…

A: pitch circle diameter (PCD) = 120 mm Angle with respect to holesat ,  H1 = θ = 60°at ,  H2 = θ =…

Q: SKETCH THE 2D FIGURE IN AUTOCAD DRAWING AND USE THE 2D SKETCHING TO FIGURE OUT THE BELOW SKETCH

A:

Q: It's known that the mechanism is a 4-bar

A: Drawing the kinematic diagram of the mechanism as shown below, (a) Calculating DOF: DOF can be…

Q: ect with dimension. mode 50 R20 Ø20 25 15 Ø32 Ø60 80 45 50 60

A: According to the details provided in the question, we need to DRAW the half sectional view of the…

Q: Based on Figure 3: draw the section view along the x-x cutting plane line.  i) Complete the section…

A: Please refer the following image for required sectional view of the given object. 1 Grid = 1 Unit

Q: Can you help me with this problem? P1 is where the blue dot is

A: 1. N10 G90 - Set to absolute positioning.2. N20 G54 - Select the work coordinate system.3. N30 G00…

Q: A stepper motor is used to drive an x-y milling machine table. If the step angle of the motor is 1°…

A: Given, Step angle of the motor, α=1°Pitch of the lead screw,p=7mmSpped, V=25.0mm/sDistance moved by…

Q: 2 600 STOP SIDE SECT OF TIMEL 12 €7790100-17 2E00073 13121425675 2272-5003 112 991 10130780053-933…

A: The number of pieces in the given figure

Q: Why Fsin40= 80*9.8 how can I know is Fsin40

A: Given Data

Q: ***Solve the following problems, correctly and systematically, and show all the necessary figures.…

A:

Q: My Home Duty 2: Found in a cylindrical turning process of a 24mm round shaft, the life of the…

A: Taylor's Tool lofe equation gives the direct relation between life of the tool(T) in minutes and…

Q: Determine the following based on the given: a) velocity of point A (in/s), b) the angle of Va with…

A:

Q: The angle of twist for a circular shaft subjected to a twisting moment is given bythe equation 0 =…

A: Given Data: The given relationship is θ=TLGJ The angle of twist θ is a dimensionless quantity. Its…

Q: (b) A solid right circular cylinder has radius r and height h. A plane passes through a diameter of…

A: Volume of Cylinder = πr2h Volume of Cone = 13πr2h   Volume of Remaning part = πr2h - 13πr2h = 23πr2h

Q: Question 2/ 25S+4 A) Solve the equations: (S+2)(S+7)

A:

Q: Draw the following views in Orthographic Third Angle Projection. 10:35 am 20 80 20 10:35 am

A: Given Data: Isometric view of the figure

Q: Graph about the imagen

A: The given equation appears to involve Dirac delta functions, denoted as δt. The equation is: To…

Q: Draw figure (3) by using circle, polyline, loft, slice and union.

A:

Q: Given x-[2 13 7.9 4 6] explain what the following command do: 1- X(3) 2- X(1:7) 3- X(1:end) 4-…

A:

Q: Figure shows a two-arm robot manipulator. The lengths of the arms are 5 and 7 m, respectively.…

A: Solution: Given Data: L1=5 mL2=7 m   To Find: The range of angles.

Q: In a rotating body, if it rotates at 2045 revolutions per minute.What would be the angular velocity…

A: Angular velocity Angular velocity is the rotational velocity of a body. It is equal to the angular…

Q: Draw the figure using the Auto CAD commands and dimension it R20 R120 R110 R10

A:

Q: Draw the three projections of the following shape: 50 R15 4 HOLES Re DIA12

A:

Q: Q7) If point A and B are center for fillet of R10 and R20 respectively. What is the length of…

A:

Designing techniques

Engineering design is described as a method that engineers use to identify and solve a problem by taking a fixed series of steps. The engineering design process involves designing a component or machine element that satisfies certain criteria or performs a specific function. This includes designing, building, and testing the product or machine element.