If material has 57% fines, 30 % Sands, 15% Gravel and a liquid limit of 39 and a 15 PI. what is the Group Symbol and Group name

Q: The bent bar whose mass is negligible is supported at one end by a pin and leans against a smooth…

A:

Q: Show complete and clear solution. Don't round off initial values, round off final ans only pls

A:

Q: The uniform 25 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional…

A:

Q: Manov Steel Inc. has a rolling mill that produces sheet steel with a nominal thickness of 0.125…

A:

Q: Quartering (or splitting) means reducing sample sizes into reasonable volumes. Would you expect…

A: The process of reducing a sample of aggregates to a required size and divide the sample into two or…

Q: Give five reasons why the study of clay minerals is of importance. State six uses of kaolinite

A: Study of clay minerals is important because 1.It provides the structure of the minerals. 2.It…

Q: What are the three mineralogical or geological classifications of rocks, and how are they formed?

A: Geologists classify rocks into three groups: 1) Igneous rocks 2) Sedimentary rocks 3) Metamorphic…

Q: compare the Physical and mechanical properties of aggregate?

A: Brief concept- Aggregate- Aggregates are used to make concrete in the building construction works.…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A:

Q: From Data What is Material Ultimate Strength In Mpa. 1 Material Aluminum 2 Form Cylinder ve 3…

A:

Q: Distinction between clay minerals and nonclay minerals.

A: Clay minerals are hydro-aluminium phyllosilicates, which can also contain alkaline earths, iron,…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Given that,   The volume of rigid bucket= 0.2 ft3      Weight of empty bucket= 18.2 lb  Weight of…

Q: The weight of aggregate having specific gravity 2.65, completely filled into a cylinder of volume…

A:

Q: What will be the relation between E and K Where, E= Young's modulus and K= bulk modulus when…

A: Given. What will be the relation between E and KPoisson's ratio=0.30

Q: briefly explain the geological properties and aggregates which determines their acceptance for use…

A: Introduction:- The Properties of aggregates, The Aggregates are utilized in concrete to reduce the…

Q: Specific Gravity and Absorption of Coarse Aggregates What are the possible discussion of…

A: There are two types of  aggregates, they are fine aggregate and coarse aggregate. Coarse aggregate…

Q: In a shape test of aggregate, which one the following gives the correct slot for flakiness index for…

A:

Q: what are the different classification of water hardness

A: Given data in question  Hardness  To find out  Classification of water based upon hardness

Q: choose true or false  If you know that weights of coarse aggregate as follow :Weight of aggregate…

A: Given data : A= Weight of aggregate stock = 5350 gm, B= weight of aggregate in oven dry= 5200 gm, C=…

Q: If Slump=120 Maximum size of aggregate=25 How is the amount of water interpolated ?

A: Basically, interpolation of data is done to know the exact value of variable which cant be predicted…

Q: Table shows the grain size distributions of aggregates A, and B. Answer the following questions and…

A: Given: The grain size distributions of aggregates are shown below,

Q: Referring to the aggregate gradations A, B, and C in Figure , answer the following questions:a. What…

A: Consider the figure of aggregate gradations.

Q: Why the specimen used in a ductility test of bituminous material is briquette shaped??

A: One of the main reasons for maintaining a briquette shape of bitumen in the ductility test is that…

Q: Referring to the aggregate gradations A, B, and C in Figure P5.26, answer the following questions:…

A: Given values: Consider the graph given.   Maximum size of aggregate is the smallest size of sieve…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Solution: Given:   A B C bucket + aggregate (kg) 34.75 34.06 35.74 Wet Mass (g) 521 522.4…

Q: State four failure modes of materials. Describe typical examples of each mode.

A: The four failure modes of materials are Fracture fatigue General yielding Buckling Excessive…

Q: How and Why is the Hardness of Mineral important in Civil Engineering? Provide a thorough discussion

A: Hardness Hardness is defined as the resistance of a mineral to the scratching. It is a specific…

Q: List some Clay minerals and their uses.

A: Clay is a fine-grained soil and having the nature of stick each particle with each other. Clay is…

Q: Quartering (or splitting) means reducing sample sizes into reasonable volumes. Would you expect…

A: Whenever a mechanical splitter is unavailable if the aggregate is damp or compressed, quartering is…

Q: A 460 mm x 510 mm rectangular concrete interior column is reinforced with ten - 19-mm-diameter bars.…

A:

Q: What are the categories of bulky grains? Explain its features.

A: - Bulky grains is type of soil grain which has all dimensions that are length, width and thickness…

Q: the resultant of the parallel force system is 800 lbs downward, what is its location from the…

A: To find value of P

Q: Situation 1. From the given data of materials retained between consecutive sieves, compute the value…

A:

Wind Energy

Wind energy is a renewable energy source that is used to generate electricity by wind power. The term, wind power, means utilization of kinetic energy of wind to generate electricity. Wind energy is termed renewable source energy because it can never be exhausted. There are other renewable energy sources, such as solar energy, geothermal energy, hydropower energy, and so on. All of them contribute to power the thermal energy stations to generate electricity.