If light machinery oil has a viscosity of 5E-2 Pa-s and density of 970 kg/m³ at 25°C, how long will it take for a sample to pass through a viscometer if water under this condition takes 1 min? Density of water is 1000 kg/m³ and its viscosity is 8.9E-4 Pa-s. A. 36.5 min B. 47.7 min C. 57.9 min D. 64.4 min

If light machinery oil has a viscosity of 5E-2 Pa-s and density of 970 kg/m³ at 25°C, how long will it take for a sample to pass through a viscometer if water under this condition takes 1 min? Density of water is 1000 kg/m³ and its viscosity is 8.9E-4 Pa-s. A. 36.5 min B. 47.7 min C. 57.9 min D. 64.4 min

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter32: Gas Chromatography

Section: Chapter Questions

Problem 32.15QAP

See similar textbooks

Similar questions

When 10 mL of water at 20oC is placed in an Ostwald viscometer, it takes 136.5 s for the liquid levelto drop from the first mark to the second. For 10 mL of hexane at 20oC in the same viscometer, thecorresponding time is 67.3 s. Find the viscosity of hexane at 20oC and 1 atm.(ηH2O=1.002 cP, dH2O= 0.998 g/cm3, dC6H14=0.659 g/cm3)
A capillary viscometer was used to measure the viscosity of a fluid at room temperature. At a pressure drop per unit length of 0.28 mmHg cm−1, i.e., ΔP/L, the measured flow rate of the fluid through the capillary viscometer was found to be 0.0125 cm3 s−1. When the value of ΔP/L was increased to 0.79 mmHg cm−1, the flow rate of the fluid was found to be .047 cm3 s−1. Under these conditions, is the fluid Newtonian or non-Newtonian? Be sure to justify your answer.
The time of efflux of water through an Ostwald viscometer is 0.60 minutes. For the same volume of an organic liquid of density 1.75 g/ml the time is 1.25 minutes. Find its absolute viscosity at 20° C is 1 cP.
2. A three-point loading scheme for measuring the stress-strain behavior and flexural strength, σF, (stress at fracture) of brittle ceramics for rectangular and circular cross sections materials are shown below. 3FfL = πR³ 2bd2 (depending on the FfL The flexural strength σF, can be calculated as: σFƒ cross section shape). = Calculate the ceramic flexural strength when Fƒ=1030 N, L=3.5 cm and 2R=b=d=1 cm and define which structure is stronger. Show your work. Note when you calculate, don't forget to unit conversion! Ff R Compression Tension
When the temperature is 20 ° C, water flows through an ostwald viscometer at 363 s, whose density and viscosity are given as 0.9982 g / cm3 and 1,000 cP, respectively. The flow time of OF2 from the same viscometer at -145.8 ° C was measured as 68 s. Since the density of OF2 at this temperature is 1.523 g / cm3, what is the value of its viscosity?
Ascetic acid with a specific gravity of 3.25 has a kinematic viscosity equal to1.35 × 10-6 m2/s , what is its dynamic viscosity?
I want the Calculation for this observation
If the flow time of water at a temperature of 20 ° C in the viscometer equals 427.5 seconds. Calculate the viscosity coefficient of mercury (its density equals 13.6 grams per cm3) if the flow time of mercury under the same conditions is 48.4, noting that the viscosity of water is equal to 3-10 * 10.05 Poise.
You are given three unknown samples stored in screw-cappedcontainers and was told to analyse them. You noted that Container A iscloudy and have some particles that are staying near the bottom of thecontainer. Container B is translucent while Container C is transparent. If thecontents of Container A can be separated by simple decantation,what isthe particle size that BEST describes its composition?i. <1 nmii. 1 nmiii. 1 nm-100 nmiv. >1000 nm
Phosphorous is predeposited at 4.5 x 10^20atoms/cm^3 on a silicon wafer with an initial concentration of 3 x 10^15 atoms/cm^3.This process was conducted for one hour at 975 degree C with D = 1.6 x 10^(-3)m^2/hr. Calculate the concentration at the diffusion depth.
An oil is flowing between tank A from a cast iron pipe with a diameter of 15 cm and a length of 150 m to point B, at an elevation of 30 m. What pressure do we have inside tank A. so that 13 1/ ves Yoli=0.84 T /m3 and kinematic viscosity 2.1* 10– 6 m2/ sDipò sit A tancat
η helium = 1.88 x 10-5 Pa s at 0 C, calculate the diffusion coefficient and the thermal conductivity coefficient.