If elements A and B are attached to element C in the figure below, while element D is the assembly unit, determine the probability that this assembly will fit freely (i.e. it will not be a forced fit). 80 ± 4 mm 81 ± 4 mm A! D o 12 ± 1 mm O 24 + 2 mm 16 +2 mm

Q: A compressor motor has a shaft diameter of 7⁄8 inch. The felt wiper that wrapstightly around the…

A: Given    Diameter,d = 7⁄8 inch.

Q: Determine the setting for a straight spur gear having 46 teeth of module 4 mm.

A: Given Data⇒ Straight spur gear : Number of teeth(t)=46 teeth Module(d)=4 mm

Q: The triple thread screw has a lead of 15 mm. Determine its thread per inch.

A: Given               Lead, L = 15 mm                           = 0.59 in No of thread, n = 3 Find…

Q: The radial distance measured from the pitch circle of a gear to the top of the gear tooth is known…

A:

Q: 4. In what standard plates can we index the following. Solve using sil label each values. a. gear of…

A: we have to determine the plate size for manufacturing the given items by simple indexing

Q: thread the outer Jiem 10

A: Given data Outer diameter =26mm Inner diameter =18mm

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Determine the thickness (mm) of a spur gear tooth with a diametral pitch of 7.01, measured along the…

A:

Q: The center distance between the two gear is 250mm and module is 5cm. Find the number of the teeth of…

A: module=diameter/teeth

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: Find the moment of inertia on the side 12 The answer is within an hour

A: It can be seen that that the coordinate axes are drawn and a vertical axis also drawn parallel to…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: A compound gear train with gears P,Q,R and S has number of teeth 30, 50, 20 and 30 respectively.…

A: Given that: Number of teeth in gear P, Q, R and S are 30, 50, 20 and 30 respectively. Gear Q and R…

Q: Simple gear train has/have gear/s on each shaft. O two O two or more coaxial gears O two or three O…

A: Question:- Simple gear train has/have ONE gear on each shaft. Two Two or more coaxial gear Two or…

Q: Tapered gibs are adjusted by screws spaced out along the length of the gib. Select one: O True O…

A: Tapered gibs

Q: A belt drive consists of pulleys of one pulley of diameter 667 mm and another pulley of diameter 321…

A: Given data,  D=667 mm  d= 321 mm  Cross belt arrangement  Center distance arrangement x= 2.6 m…

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: please solve the centroidal  Ixc, centroidal Iyc, Ix and Iy of the attached figures

A:

Q: n find the speed of the gear F.

A: Given data: A compound train consists of six gears. the  no teeth on gears as follows:NA=100…

Q: 4 in 2 in 4 in 8 in -12 in 16 in-

A: Given data To determine the moment of inertia and radius of gyration about x and y axis

Q: To take an angular measurement with an accuracy of 5 minutes you can use: Select one: O a. Vernier…

A:

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A:

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: Construct the third projection of the cylinder.

A: According to the details provided in the question, we need to find three views.

Q: 1 mm 10 mm 1 mm Y axis 5 mm 10 mm 1 mm X-axis

A:

Q: Gear 2 in the diagram below is driven at a speed of 126 revolutions per minute. Gear 2 has 16 teeth,…

A: The gear train is simple,The speed ratio of a simple gear train with 2 gears is as follows,Here,N is…

Q: For practical working gears as manufactured, typically the addendum, a, is larger than the dedendum,…

A: Addendum: The distance between the top land and the pitch circle on a gear tooth, is called as…

Q: o shafts 3679mm between centers carry pulleys 1288 mm in diameter and 910 mm in  diameter…

A: dL= diameter of larger pulley dS= diameter of smaller pulley C= distance between the centers of…

Q: For the following internal dovetail, if bis 40mm greater than c, m is 60mm less than b, h is 25 mm…

A:

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A: As per given question  The radial distance measured from the pitch circle of a gear to the bottom…

Q: Number of teeth are indicated for the following gear train. Driver gear 2 has speed 1200 rpm in CW…

A: Given, T2 = 10 T3 = 30  T4 = 16 T5 = 32 N2 = 1200 CW = +1200   Note: Clockwise rotational speed is…