If DA = 17cm, DB = 12cm and L = 4m, and if oil is flowing at a rate of 0.08 m³/ s, determine the difference in pressure %3D between sections A and B. Neglect head losses. |DB - В z (vertical) L DA – A

Q: 7. A 6-in.-long bronze tube, with closed ends, is 3 in. in diameter with a wall thickness of 0.10…

A:

Q: 4.5.4. If the pressure difference bet will be the flowrate? The pipes are 10° ft/s and neglect minor…

A:

Q: Three pipes 1, 2, and 3 are connected in parallel and a fourth pipe is connected at B. The…

A:

Q: The

A:

Q: At A, water (rho=1000kg/m* 3 and mu=1cp) at a pressure of 400 kPa and a velocity of 3 m/ s, flows…

A:

Q: The diameter of a pipe carrying oil (s=0.92) changes gradually from 400 mm at A to 600 mm at B.…

A: To Determine (a) The direction of flow; (b) the frictional loss between the two points.

Q: PB = 2.3 PA 2 bars 30° 2m

A: Pressure at A, PA=2 bars =200KPaPressure at B, PB=2.3 bars =230KPa.Diameter of pipe at A,…

Q: Water flows from A to E through the pipe system shown. It is known that the flow in pipe BFGC IS 30…

A: PIPE DISCHARGE HEAD LOSS HEAD AVAILABLE AT STARTING POINT HEAD AVAILABLE AT END POINT AB 165.27…

Q: The pressure gauges are inserted at A and B in a vertical pipe converging water.  The diameters at A…

A:

Q: The inverted U-tube manometer contains oil (0.90) and water as shown. Oil h 0.2 m 0.3 m Water

A:

Q: A/ In the pipe systems show, find the distribution of flow, with a friction factor of 0.0165. Assume…

A: At junction A1: Qin=Qout 2=QAG+QAC+QAB 2=0.658544+1.02634+QAB QAB=0.31511 m3/s

Q: Three pipes 1, 2, and 3 are connected in parallel and a fourth pipe is connected at B. The…

A:

Q: he diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than…

A:

Q: In the figure, friction loss between A and B is neglected while between B and C it is 0.2 (VB²/2g).…

A: Given, In figure, The diameter of pipes A&C = 443mm =0.443m Diameter of pipe B= 131mm= 0.131m…

Q: gure AG E 400 mm < 1 of 1

A:

Q: For the conditions shown in schematic 1m figure, find the force F required to lift the Absolute…

A:

Q: 3. Obtain the gage pressure at the center A of the pipe shown. Ignore surface tension effects.…

A:

Q: H.W.11// Determine the gage pressure at the center of pipe A in pounds per square to kN inch and in…

A:

Q: a)Determine the difference in pressure between A and B in kPa if h = 0.15 and SG of oil is 0.862.…

A:

Q: Bernoulli/continuity) Water flows steadily through the pipe shown in the figure below such that the…

A:

Q: 4) Water flows through a contraction section as shown. A pressure gage connected between the…

A:

Q: 2-46. The two pipes contain hexylene glycol, which causes the differential pressure reading of the…

A:

Q: diameter. 11. The maximum force exerted by a small bydraulic press is 500 kN. The working pressure…

A:

Q: Determine the gage pressure at the center of the pipe (point A) in pounds per square inch when the…

A:

Q: A/ In the pipe systems show, find the distribution of flow, with a friction factor of 0.0165. Assume…

A: For each pipe -  Qin = Qout   At junction A -  Qin = Qout⇒ 2 = QAC + QAG + QAB⇒ 2 = 1.0264 + .6586 +…

Q: What is pipe roughness? A pump is located 5 m above the surface of a liquid (y = 8170 M/m³) in a…

A: Given Data : f= 0.03 Dia (d)=0.2 m length (l)=60 m Power = 1.5 KW= 1500 W Length of suction pipe =…

Q: A swimming pool has a width of 4 m and a side profile as shown. Determine the resultant force the…

A: Width = 4 m CD = 1 m AB = 2.5 m BC = 8 m

Q: If the pressure head in pipe A is 2 m of water, determine the pressure in pipe B. ‚OIL of Sp. gr.…

A: Given: Pressure head in A = 2 m of water Specific gravity of oil = 0.8

Q: Q2-b)- For the setup shown , determine the pressure, elevation and total head at points A, B, C , D…

A: Pressure is the power applied opposite to the outside of an article for each unit area over which…

Q: Determine the maximum diameter of the cylinder tank

A: Internal Pressure=127 kPa = 0.127 MPa Allowable longitudinal stress=140 MPa Allowable tangential…

Q: section 1, Q1= 0.11 m^3/s and p1= 138 kPa. d2=100mm 309 (2) water 2, d,=150mm 13 50 Od:375mm

A: Q1=0.11 cumec P1=138kPa

Q: Assignment -2: If the pressures at pipes 1 and 4 are 30 kPa and 120 kPa respectively, determine the…

A:

Q: Q1 Given is a three-pipe series system, as in Fig. The total pressure drop is py — ps = 150,000 Pa,…

A: Consider the data Calculate the total head loss in the system

Q: Determine in psi the pressure drop between the ends of this duct.

A: Given data: P1=0.0406 lb/in2. P2=0.022 lb/in2.

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?