diameter. 11. The maximum force exerted by a small bydraulic press is 500 kN. The working pressure of the fluid is 20 N/mm?. Determine the diameter of the plunger, operating the table. Also suggest the suitable thickness for the cast steel cylinder in which the plunger operates, if the permissible stress for cast JAns. 180 mm ; 20 mm

diameter. 11. The maximum force exerted by a small bydraulic press is 500 kN. The working pressure of the fluid is 20 N/mm?. Determine the diameter of the plunger, operating the table. Also suggest the suitable thickness for the cast steel cylinder in which the plunger operates, if the permissible stress for cast JAns. 180 mm ; 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

thanks in advance
Not sure how to do this one. Would really appreciate a full solution. Thank you!
Q3: . A crank built up from cylindrical sections by welding required a loading of 250 lb to overcome the resistance when in the post- tion shown. (a) Compute the maximum normal and shear stresses induced in the section A-A. (b) Determine the maximum shear stresses induced in parts I, II, and III. Ans. (a) (max) = 29,000 psi, T(max) = 15,000 psi (b) 10,550 psi for part I, 6880 psi for II, 15,000 psi for III --A III II 1 Dia. Dia. Fig. 2-38 250 lb 150 "Dia.
What are the assumptions for the cylindrical and spherical vessels such that the stresses are calculated as follows for the cylinder: in the Hoop direction: o = pr/t the Longitudinal stress: o = pr/2t and for the sphere: O= pr/2t Cevabınızı biçimlendirmek için düzenleyiciyi kullanın
The elliptical pipe carrying steam at 3.5 mPa has an outer major axis length of 500 mm and an outer minor axis length of 400 mm with a wall thickness of 10 mm. A gasket is inserted between the flange at end of the pipe , and a flat plate is attached using 40 mm diameter bolts to cap the end . The allowable Stress in the bolts is 80 Mpa. How many bolts must be used to hold the cap if there is an initial stress of 30 mPa ?
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.500 in. and a wall thickness of 0.500 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.000-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). The bar is loaded as shown. Assume L1= 55 in., L2= 40 in., L3 = 25 in., R = 31 kips, Q = 11 kips, and P = 27 kips. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A. (c) the maximum normal stress in the entire axial assembly. R A B R L1 L2 L3 Answers: (a) 81 i in. in. An (9) (c) Omax i ksi
i need the answer quickly
please show complete solution and avoid truncation in the middle of the solution. Thank you. (EXACT ANSWERS ONLY)
Please answer in 1hr thank you
Q-2 The rotating shaft running at n = 900 rpm, shown in the figure below, is machined from AISI 1045 CD steel. It is subjected to a force of F = 10.1 kN. The shaft is experiencing an operating temperature of 35 oC. With the specified loading and for a reliability of 99.9 %, a) Determine the minimum factor of safety for fatigue based on infinite life*. b) Determine the maximum safe load (Fmax) that can be applied for a factor of safety of 1.5 and a design life of 5x105 cycles, all other input values remaining the same. c) Determine factor of safety against yielding. *Free-body, shear-force and bending moment diagrams are required.