Iculate the maximum allowable force "P" that can be applied without causing the weld to Use the Elastic Method -24"- 1/4 P

Q: Determine the shear Load that act on the fillet weld that joining two plates together if the working…

A: Length of the weld  = l = 7inThickness of the plate = t = .5inWorking stress = δ = 11300lb/in2.

Q: Calculate strength of single V butt joint to join 2 plates 300 x 16 mm with fy = 250 MPa. Assume…

A:

Q: Q3. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of…

A:

Q: The connection of the drawbar and tie plate combination given below will be made by welding with two…

A: Welded connections: The point at which two or more pieces of metal are joined together is known as…

Q: Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of…

A: Given strength of fillet weld 94 mpa  Size of fillet weld = 8 mpa  Load to be carried = 185 kn

Q: 2. Determine the lengths of the side fillet welds required at the heel and toe of the angle shown.…

A: Given shear stress in weld   = 124  MPa For plate thickness 13 mm minimum size of weld  =5 mmand…

Q: afe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit…

A:

Q: A hanger is suspended from a plate that is welded to a wide flange beam as shown. The plate requires…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Find the Load Capacity of the weld if the throat thickness is 8. 13 mm, Nominal Tensile Strength, Fu…

A: t = 8.13 mm l = 400 mm  Fu = 520 MPa = 520 N/mm^2  P = ?

Q: Determine the lengths of the side fillet welds required at the heel and toe of the angle shown.…

A:

Q: Problem 3 The steel (E = 30,000 ksi and v= 0.30) cylindrical tank shown below is fabricated from…

A:

Q: Determine the maximum effective net area of the fillet weld using the maximum weld allowed by the…

A:

Q: Compute the size of fillet weld for a bracket connection with ISMB 300 column as shown in figure.…

A:

Q: A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN…

A: Retaining walls are moderately robust walls used laterally to hold soil so as to be retained on both…

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate- Fy = 248 MPa Fu =…

A: Given;

Q: A 4 x 4 x ½ - in. angle of A36 steel is to be welded to a plate with E70XX electrodes to develop the…

A: Calculate maximum allowable tensile stress as; FT=0.7FY=0.7×36=25.2 ksi Calculate the maximum…

Q: A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back…

A: Slot Weld : Slot weld is used to attach flat plates using one or more holes in the top part. To fuse…

Q: The allowable unit stress in shear on a fillet weld is 15,000 psi, and the total actual length of…

A:

Q: cank has an inside diameter of 48 in normal stress perpendicular to the 55 O 480 psi

A:

Q: The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of…

A: Given data: P=9600 lb Permissible shear stress, PSS=13600 psi Length of weld, L=3 in. Weld size=?

Q: Q4) Determine the maximum service load than can be applied if the live load to DL ratio is 2. All…

A: The given data is: Grade of Steel=A 36 Member designation=L 5*3 1/2*5/16 Ag=Gross area of…

Q: 3.2 A load is applied 100 kN inclined at 30 to vertical in clockwise direction, check whether the…

A:

Q: The angle 150x100x10mm is connected to a 8.5 mm gusset plate. The size of weld is 8 mm and using E70…

A: a) Find the length of the weld required at the toe of the angle.b) Find the length of the weld…

Q: Design a double angle tension member that is fillet welded to a gusset plate. Assume that the angles…

A: 1).Design and select a trial tension member  See Table 5-8 on page 5-49 of the AISC manual. - Select…

Q: the allowable tensile load on the members and weldlength and overlap length of

A:

Q: A tension member consists of a double angle section with long legs back to back. The angles are…

A:

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu =…

A:

Q: Determine the size of the weld using E60 electrode. Dead Load = 38 kip and LL = 95 kips (Service…

A: Nominal strength of  weld is given by Rn = fnw*Anw fnw = Nominal weld strength fnw = 0.6*fEXX  fnw =…

Q: b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a…

A: Solution Given data Length of gusset plate L=140 mm Width of gusset plate b=320 mm

Q: Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle…

A:

Q: Regardless of the design load, the effective length of a 5/8 in. fillet weld that is subjected to…

A: To determine the minimum effective length for given weld size.   Given, Weld size = 5/8 in.   As per…

Q: A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN…

A: Fillet welds are normally some of the most widely used joints in the welding field. It is the joints…

Q: Determine the available tensile capacity of the connection shown in the figure. The yield stress of…

A:

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur,  chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.