I V R 100 0.25 4 2

Q: 4. Find the gain of each amplifier in Figure 1-6. If a signal voltage of 10 mV rms is applied to…

A: Since you have posted the questions with multiple subparts and so we are supposed to answer 3…

Q: Vdd 2.7K R 10.6V 20uA B=100 VE 8.2K 1.2K

A: Transistor: Transistor generally acts as an amplifier. It’s generally used to amplify a weak…

Q: Compute for 11. *

A:

Q: Determine ID1. 3.3 ko Si 20 V Ge 5.6 kn

A: To solve above mentioned problem, one should have clear understanding of working of diode. A diode…

Q: Q1 (a) State and sketch all possible types of dependent sources. (b) Determine Ia, Ib and Ie using…

A: This question belongs to circuit theory . It is based on the concept of kirchhoff's current law and…

Q: 4. Calculate Vout. Si R2 Vout ? 4.7kQ -w- 10V .R1 22.2kQ

A: As per our policy, i have attempted only one question. Given data is - Vin=10 VR1=4.7 kΩR2=2.2…

Q: Figure 2 shows the step responses collected from a number of different systems. For each response…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Determine Ip1- 0.33 kO D2 10 V SL Ge 02 The answer should be expressed in mA. NC

A:

Q: E R1 R2 R3 R4 RT Vr1 VR2 VR3 VrA IR1 Ir2 IR3/R4 IT PRI PR2 PR3 PT 10 1kO 1k0 1kQ 1kn C oor 1401 1.…

A:

Q: 50 10 Ω 20 N Rin 12 N 3 N

A: Now, 6Ω and 12 Ω are in series and then parallel to 20Ω. Thus equivalent of these resistors is…

Q: 1. Solve for all current values though and voltage across each resistor.

A:

Q: I. Complete the Table: Round off answers up to the3rd decimal place. Number 1 3 4. 8 9. 10 V 120 5…

A:

Q: 15. R equivalent AO R, 300 R2 600 R,

A:

Q: 10A 6A 8A 7A Io Calculate the value of lo (in Amp)

A: Apply KCL at node connecting the 5 resistors to find current Io. According to KCL sum of the…

Q: Determine mention voltages ?

A: Given circuit is drawn below:

Q: R1 10 K R2 10 KD ww R3 20 k www R4 200 ww ww RS 10 k R6 20 k ww RT 10 k

A:

Q: Determine ?1to ?5.

A: The given circuit is shown below:

Q: Question 20 The roots of the characteristic equation of Figure 3 are given by a. -60,000 rad/s and…

A:

Q: Problem 4) Determine the Thévenin equivalent circuit attached to the labeled impedance ZL. What load…

A: Given Data:An AC impedance circuit with,Supply voltage To Find:Thevenin's equivalent circuit.The…

Q: 1 femto equal to 1x10-15. Select one: O True O False

A: Femto is used to measure small values such as femto farad (fF).

Q: Determine RT (in ohms)

A:

Q: R, R2 R3 Total E 9. 9. Volts Amps R 10k 2k 1k Ohms

A:

Q: 0.392 470 650 240

A:

Q: Qrfind Current Ehrough Ry use ohm Laws In micro omper unit? 34.7310k. 333k76-8

A: Net resistance faced by 10 V source is :- 6.8k + [33k ll (22 + (10k ll 4.7k ) )] = 21 kohm.   So…

Q: Determine I. 6V 4A (1 qv 3V

A: In this question we will find current I...

Q: R. R R2 200 努 Vr= 25V Rs 40 302 Re

A: The circuit is given as below We need to calculate             E1=Drop across R1E2=Drop across…

Q: please help me make this into a hybrid pi model.

A:

Q: a d. 42 42 3Ω 3Ω h

A: Given

Q: Problem 5. In the circuit shown to the right, the voltage and current expressions are v = 100e-80 V,…

A: Since multiple subparts are asked, as per Bartleby guidelines only the first 3 subparts are…

Q: For the circuit shown in the figure, the value of the current i is: 50

A:

Q: 85 452

A:

Q: Determine IT (in Amps) 50 102 252 IT 12Voc 50 7.50

A:

Q: 50Ω WW M b 3.2 d €250 3.50 a 452 W M 6Ω M 5Ω 5Ω C 2.02 e 75.0 10022 M f

A:

Q: Solve it with nodal analysis , please.

A:

Q: 5. Calculate the value of RL across A and B. 3 ohm A 5 ohm B 4 ohm 20V 10V 2 ohm 3 ohm a) 3.45ohm b)…

A: we need to calculate value of RL.

Q: 1.25A R 50 Ω 50 V 20 Q 40 Q 30 Q Find the value of R

A:

Q: £T = ? 0.25F //20 6. 2H 0.5F £T

A: In this question we will find Laplace transform.... Note:- as per our guidelines , I will answer…

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.