(i) The reaction at the fixed support "A" (unit in N)=_(ii) Shear force at the point "A" (Unit in N) =(ii) Shear force at the point "E" (Unit in N) =%3D Draw the Shear force diagram & Bending moment diagram for the cantilever beam as shown infigure, mark the salient points in the diagram. Neglect the self-weight of the beam, where F1=10 N, F2 =60N, F3 =30 N, F4 =10N, a =5 m, b=2 m, c=3 m, d=5 mF4F3F2F1EAd.a

(i) The reaction at the fixed support A. Taking resolution of vertical forces, RA=10+30+60+10RA=110…

Answered: (i) The reaction at the fixed support…

(i) The reaction at the fixed support "A" (unit in N)=. (ii) Shear force at the point "A" (Unit in N) = (iii) Shear force at the point "E" (Unit in N) = %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A simple beam is shown in Figure Q2(a) has three concentrated loads at the position indicated. The…

A: Given- Diameter (d) = 200 mm Let support reaction at support 1 and 2 be R1 and R2 respectively

Q: OD aluminum steel A composite beam is a built-up section made of aluminium and reinforced with a…

Q: P=197 KN L1= 1m L2= 1.4 m L3= 2 m L4= 4m a.) Determine the shear force at point D. b.) Determine the…

Q: QUESTION 4) For the given system shown in the figure, the AB bar is in the 4m direction of z-axis…

A: Given: The diameter of OB and AB, D = 100 mm = 0.1 m The radius of disc, r = 0.5 m The allowable…

Q: 1. Simulate for the maximum shear stress and strain on a beam as shown in figure below. 75 N 125 N-m…

Q: shown in Figure 3(a) a roller support channel section as shown in Figure 3b). Determine the support…

A: Since you have posted a question with multiple subpart, so we will solve first three part for you.…

Q: Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below.…

Q: Find the reactions by drawing a free body diagram and then draw the shear force diagram. 30 kN 50 kN…

Q: 3. A turbine shaft made from steel (E-200GPA) is exposed to a resulting load F=5417N. The supports…

Q: Q1) The stress function (x) for the cantilever beam as shown in the figure is given by: $(x) = ² (…

A: Given:To find:

Q: c) A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m…

A: Given Data The daimeter of truss tie rod is:d=9.52 mm The length is:l=1.75 m The stress experienced…

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:- Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: Example: A bar with a rectangular cross section and a central circular hole in tension F+ W O Id F w…

Q: c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) -…

Q: find second moment of area for cases 4-7

Q: Q3: A simply supported beam AB of length 6 m subjected to a clockwise couple of 24 point C as shown…

Q: The principal stresses at a point P of an elastic body are (1) = 5 N/cm², o(²) = -5 N/cm² y o(³) =…

Q: The principal stresses at a point P of an elastic body are (1) = 5 N/cm², o(2) = -5 N/cm² y o(3) =…

Q: A turbine shaft made from steel (E=200GPA) is exposed to a resulting load F-5417N. The supports at A…

A: Given : To find : Support forces Bending and shear force diagram

Q: Replace the loading acting on the beam (Figure 1) by a single resultant force. Suppose that F₁ = 500…

Q: With pressure steel tank axis α = 750 manufactured as degree angle helical welded references Tank…

Q: 2. For the force diagram shown in the accompanying illustration, draw the shear force and moment…

A: To make shear force diagram and bending moment diagram, find support reactionEquilibrium equation…

Q: Question 2. Consider the beam with a I-beam cross section in Figure 2. Consider point A at the…

Q: Determine the maximum shear force in kN in the figure below. 30 kN 140 kN • m A D В C +2 m- 3 m 2 m→

Q: II. A circular steel rod has a diameter of 50 mm. It touches the unyielding supports at point A and…

A: Given data: The diameter of the shaft is d = 50 mm. The area of the circular shaft is…

Q: ゅD aluminum steel A composite beam is a built-up section made of aluminium and reinforced with a…

A: given; ⇒bending moment (M)=4KNm =4*106 N-mm⇒diameter od…

Q: 6. x9(x) = qo sin- L Find M(x), V(x) using π.χ. d²M dx² = q(x) j

A: In this problem, it is asking about question (6) only so we will provide the solution for question…

Q: Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The weight of each pipe is The length of pipe is The diameter of each pipe is .

Q: Question 1) F = 22 kN single load, M = 30 kN.m moment and w = 6 kN/m distributed load affect the…

A: As per the company's guidelines when multiple sub parts are asked only first three has to be…

Q: The force induced in member Q.3) PQ due to load W in figure will be

Q: The simple beam with overhang carries a uniform load, w (kN/m) and a force P (kN). (aj vetemine the…

A: Please refer to the detailed solution given below, Answers - Max Stress in tension = 52.43 MPa Max…

Q: Provide information for constructing the shear diagram. The x origin is on the left at A and the…

Q: 7) Consider the beam in the figure below. Take w=50 kN/m. The 40 kN force makes an angle of 60…

Q: Substitute the value for s = 5 For the beam and loading shown. P = 20×S N, F = 10×S N, Q = 4xS N/m,…

Q: D = 90 mm d = 60 mm r = 12 mm t = 10 mm F = 9000 N What is the magnitude of the maximum stress at…

A: Given:Width of larger section, D=90 mmWidth of smaller section, d=60 mmRadius of fillet, r=12…

Q: Q2) Find the stress in steel rods BD and CE as shown in Figure due to the applied load 4 kN and the…

Q: $D aluminum steel t A composite beam is a built-up section made of aluminium and reinforced with a…

Q: 4- Draw Shear Stress-strain diagram for Cast Iron

Q: Question 1 continued 4 of 5 b) Fig. 2 shows the shear force (KN) and bending moment (KNm) diagrams…

A: The shear force diagram of the loading on the beam is shown below.

Q: a.) Determine the shear force at point D b.) Determine the normal force at point D c.) Determine the…

Q: Q2/ Draw axial, shear and bending moment diagram for the figure shown below: 3.0m 20m 30m E05

Q: 7 ►X a L a. Find reaction at x = 0. b. Find M(x) and V(x) Mo j Li 1

Q: a) Calculate the reaction forces in terms of F and theta. b) Calculate the internal shear force and…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Determine the maximum shear force in kN in the figure below. 10 kN/m 25 kN • m A E B |C D 1 m 1m 3 m…

A: Answer: The maximum shear force is +/- 20 kN.

Q: diameter of all pins is 5mm Front view • (MPa) 22mm 600 so0 180mm 120mm 0.001 0.01 top view

A: This is a case of elastic deformation of the member BD, so from the stress strain curve we can…

Question

(i) The reaction at the fixed support "A" (unit in N)=_
(ii) Shear force at the point "A" (Unit in N) =
(ii) Shear force at the point "E" (Unit in N) =
%3D

Draw the Shear force diagram & Bending moment diagram for the cantilever beam as shown in
figure, mark the salient points in the diagram. Neglect the self-weight of the beam, where F1
=10 N, F2 =60N, F3 =30 N, F4 =10N, a =5 m, b=2 m, c=3 m, d=5 m
F4
F3
F2
F1
E
A
d.
a

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. The stress-strain diagram for a bar of steel alloy is shown. Determine: a) The modulus of Elasticity for the material b) The proportional limit c) The ultimate stress d) The modulus of resilience e) If the bar has a circular cross section with an initial diameter of 10-mm and is loaded to 260-Mpa, what will be the decrease in diameter under this load? Use v= 0.25 (MPa) Show complete solution.
P= 4 kN w= 0.8 kN/m a) Start with the shear diagram. To use a segment of the left end of the beam to develop the expression for the shear, the vertical reaction at A must be known. Calculate the vertical reaction at A. Let a positive force act up. b)Write an expression for the internal shear for an arbitrary point between A and B c)Write an expression for the internal shear for an arbitrary point between B and C.
What is the Shear Force,V?
For the system below b=0.04m, h=0.08m a) Calculate the reaction forces in terms of F andq.b) Calculate the internal shear force and moment as a function of x using cuts and summingforces and moments in terms of F, L, andq.c) Calculate the shear force and moments by integration in terms of x, L, F andq.d) Assuming a rectangular cross section compute the average normal stress for the case F =10kNat 30° where b =0.04 m, h = 0.08 m, at the point x = L/4, L = 1 m at the centroid.e) With the cross section given above compute the average normal stress for the case F =10kN at30° at the point x = L/4, L = 1 m at each surface of the beam.f) Calculate the shear stress at the top and bottom surface, at the neutral axis and at x = 0.25 mand y = 0.02 m above the neutral axis.
!
Draw shear force and bending moment diagrams P= 1000 N .w = 250 N/cm 5 cm 20 cm Figure 1.2 (not to scale)
Q5: As shown in Figure (4.16), the maximum shear stress at section (a-a) is (29.47 MPa). If (b =12 mm), (r-250 mm),(G-84 GPa). Find: 1) The torque T, and 2) The angle of rotation at section -b). (b 3T 1m 0.9 m 0.6m
7 The Questions Question 4. X Given, B cere RD 26.25 C F = 90 kN, UDL = 40 kN/m UDL The above figure (not drawn to scale) shows a 6 m long beam subjected to a force F and a uniformly distributed load UDL. kN D 補 I»I»I»] Length X = 2m, Length Y= 0.5 m Calculate RB and RD, the vertical reaction forces at the supports. Enter your answers in kilonewtons (kN), correct to 3 decimal places, in the boxes below. RB
H2.
3.3 m 4,9m Ax = 23.370 mm %3D Interconnected rods up to 23.370 mm from the right end it's pulled and fixed. Length of Bar No. 1 3.3 m, cross-sectional area 2.4 cm2 and yield stress 215 MPa; No. 2 length of Rod 4.9 m, cross-sectional area 2.8 cm2 and yield its stretch is 387 MPA. Elasticity of both materials module 207 MPa and materials elastic / excellent since it's plastic: How much plastic elongation amount of Bar No: 1 meters? How many meters is the lengthening of Rod 2? How many normal stresses in Rod Section 2 Is it an MPA? 3.
!
RAX Ray 0.2m 100Nm 100N 1000 0.3m A. Draw Shear force diagram B. Draw Bending moment diagram C. Draw Torque diagram D. Draw Axial force diagram ZOON 1000m 2000 0.2m y RBy Ł 10,000 N 10,000 N