I need the expert's solution regarding branches a and b. I need a correct answer, not like the previous one. A/ A power station has a daily load cycle as under: 260 kwh for 6 hours; 200 kwh for 8 hours: 160 kwh for 4 hours, 100 kwh for 6 hours. If the power station is equipped with 4 units of 75 kw each, calculate (i) daily load factor (ii) plant capacity factor and (iii) daily requirement of fuel in kg if the calorific value of fuel used were 10,000 kcal/kg. B/ power station has a maximum demand of 15000 kW. The annual load factor is 50% and plant capacity factor is 40%. Determine the reserve capacity of the plant

I need the expert's solution regarding branches a and b. I need a correct answer, not like the previous one. A/ A power station has a daily load cycle as under: 260 kwh for 6 hours; 200 kwh for 8 hours: 160 kwh for 4 hours, 100 kwh for 6 hours. If the power station is equipped with 4 units of 75 kw each, calculate (i) daily load factor (ii) plant capacity factor and (iii) daily requirement of fuel in kg if the calorific value of fuel used were 10,000 kcal/kg. B/ power station has a maximum demand of 15000 kW. The annual load factor is 50% and plant capacity factor is 40%. Determine the reserve capacity of the plant

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Please help will like
I need the answer as soon as possible
Please answer in typing format solution
step down chopper has Vs = 230 V and R = 10 0. For a duty cycle of 0.4, the power taken by the chopper is 2097 Watts. Find the chopper efficiency. Take the voltage drop across the chopper switch as 2 V. a) 98 % b) 89.96 % c) 99.14 % d) 96.54 %
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
A) An equalizer is a jumper used to parallel the series field of two compound DC generators when the two generators are being run in parallel to share an electrical load. a) true b) false B) The ohmic value of an equalizer is not important as long as it is made out of copper. a) true b) false C) How is the efficiency usually expressed?a) in watts b) in kilowatt-hours c) in percentage d) none of the above
SHOW COMPLETE SOLUTION A. What is the overall power factor of the two loads as seen by the source? Use two decimal places. B. Determine the magnitude of the current passing through Load 1. Use amperes and two decimal places. C. Is the overall power factor leading or lagging?
I need to solve a question within 15 minutes as quickly as possible
I. PROBLEM SOLVING. The following are data pertaining to three units in a plant: Unit 1: Min: 150 MW Max: 600 MW C(1) = 0.01562 P₁2 + 79.2 P₁ + 5610 $/br Unit 2: Min: 100 MW Max: 400 MW C(2) = 0.0194 P₂² + 78.5 P2 + 3100 $/br Unit 3: Min: 50 MW Max: 200 MW C(3) = 0.05784 P3² +95.64 P3 + 936 $/br What unit or combination of units should be used to supply a load of 550 MW most economically? Support your answer with solution.
(b) A symmetrical three-wire three-phase supply as shown in Figure Q2(b) is connected to a balanced three-phase load. The value of impedance, Z is identified to be 100-j75 Q. (i) Find IaB, IBC and ICa (ii) Determine Iaa, IbB and Ic (iii) Determine Iba, Isb and Ix (iv) Draw the phasor diagram of all currents in Q(b)(i) and Q(b)(ii)
Solve b), c) and d) only