I- A mesurement system is to be used to mesure a presure of 250 Hz. For accurate readings, the time constant of the system sholud be (e) 0.01, (f) 1E-4, (g) 0.025. II- The bi-metallic thermometer is used to measure temperatures of --- variation. (a) very high, (b) very low, (c) above 1 Hz, (d) above 10 Hz, (e) above 100 Hz, (f) none of these. III- The static Pitot tube is suitable for measuring dynamic, (b) variable, (c) controlled, (d) directly constant, (e) dynamic, (f) constant. IV- The Borden-type gauge is a good choice to measure dynamic, (b) variable, (c) controlled, (d) directly constant, (e) dynamic, (f) static --------- sec. (a) 250, (b) 2.5, (c) 25, (d) 0.25, ---frequency fluid velocities. (a) directly pressures. (a) directly -------

I- A mesurement system is to be used to mesure a presure of 250 Hz. For accurate readings, the time constant of the system sholud be (e) 0.01, (f) 1E-4, (g) 0.025. II- The bi-metallic thermometer is used to measure temperatures of --- variation. (a) very high, (b) very low, (c) above 1 Hz, (d) above 10 Hz, (e) above 100 Hz, (f) none of these. III- The static Pitot tube is suitable for measuring dynamic, (b) variable, (c) controlled, (d) directly constant, (e) dynamic, (f) constant. IV- The Borden-type gauge is a good choice to measure dynamic, (b) variable, (c) controlled, (d) directly constant, (e) dynamic, (f) static --------- sec. (a) 250, (b) 2.5, (c) 25, (d) 0.25, ---frequency fluid velocities. (a) directly pressures. (a) directly -------

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. a) With neat diagram, State the principle of RTD sensor b) A platinum resistance thermometer has a resistance of 100 ohm at 25°C. The Resistance temperature coefficient of platinum is 0.00392 ohm/ohm°C. (i) Find its resistance at 700C (ii) Let the thermometer has a resistance of 400 ohm, calculate the value of temperature.
A rope-brake dynamometer attached to the crank shaft of an IC engine measures a brake power of 10 kW when the speed of rotation of the shaft is 400 rad/s The shaft torque (in Nm) sensed by the dynamometer is....
%ov li. N A نقطة واحدة The thermometer requires one minute to indicate 90% of the response curve. Assuming the first- order system response as shown below. If the thermometer is placed in the bath, what is its time constant * ?in seconds c(t) = K(1 – e-t/) %3| 23 O 26 29 32 نقطة واحدة The first-order system has a unit- ramp response as shown below. what is the transfer function of the * ?system c(t) = t – 10 + 10 e-0.1t 10/(s+1) O 1/(s+10) O E II
Hello, Please answer this question. Thank you.
A light duty sleeve bearing operates in still air at air temperature of 70 °F and sustains a load of 350 lbs. A shaft rotates at 600 rpm. The coefficient of friction is 0.015 between shaft and bearing. The shaft diameter is 1.75 in. and the bearing length is 2.50 in. Find the probable operating temperature of the bearing. A. 143.45 deg F C. 134.54 deg. F D. 125.74 deg F B. 171.7 deg. F
please read the question and note carefully
kitchen oven has a dial thermometer with a resolution of 10 degrees. The error caused by interpolation due to the use of this dial thermometer is 95% expected to be:
Please show the complete solution. Thank you
The van travels over the hill described by y =(−1.5(10^−3)x^2 + 15 ft. If it has a constant speed of 75 ft/s, determine the x and y components of the van’s velocity and acceleration when x = 50ft.
The output voltage you would expect to obtain from an LM 335 temperature transducer (IC sensor) which has a sensitivity of 10 mV/°C at -20 kelvin is: Select one: Oa. Omv O b. -200mV O c. 2930mV O d. -2930mV
Annealing is a critical process in semiconductor manufacturing where silicon wafers get rapidly heated to get temperatures using powerful infrared heaters. Annealing helps to reduce defects in materials after implantation or deposition processes. a) You have been asked to design a temperature sensor an annealer with a range of up to 1500°C.Select a suitable thermocouple from the table below and give an explanation for your choice. 80 E 70 60 K 50 40 -C 30 20 10 0. 500 1000 1500 2000 2500 Temperature ("C) b) To record the temperature, you use a microcontroller with an ADC. The ADC is referenced to a 2.048V reference voltage source. To make use of the entire range of the ADC, what gain does the amplifier require for your chosen Thermocouple? c) You want to read the temperature with a resolution of 0.5°C. What is the minimum number of bits that your ADC requires? d) The thermocouple has a time constant, t, of 300ms. If the annealer heats from room temperature (20°C) to 820°C. What…
Fourier rate equation predicts that the temperature difference is not inversely proportional to the cross- sectional area. Select one: O a. False O b. True