77. A large hydroelectric power station hasa head of 324 m and an average flow of1370 m³/s. The reservoir has an area of6400 km2. The available hydroelectric3power is(i) 2100 MW(ii) 5600 MW(iii) 4350 MW(iv) 2650 MW

Given, A large hydroelectric power station has, Head, H = 324 m Rate of flow, Q = 1370 m3/s…

hydroelectric power station has a head of 324 m and an average flow of 1370 m/s. The reservoir has an area of A large 3 6400 km². The available hydroelectric power is (i) 2100 MW (ii) 5600 MW Çiii) 4350 MW (iv) 2650 MW

hydroelectric power station has a head of 324 m and an average flow of 1370 m/s. The reservoir has an area of A large 3 6400 km². The available hydroelectric power is (i) 2100 MW (ii) 5600 MW Çiii) 4350 MW (iv) 2650 MW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 2. A generating station has a maximum demand of 80 MW and a connected load of 150MW. If MWhr…

A: Given: Maximum demand = 80 MW Connected load = 150 MW MW hr generated in year = 400000

Q: 3-phase, two-pole, Y-connected, 60 Hz, 10MVA, 13.8kV synchronous generator has a synchronous…

A: The synchronous generator can be solved as following.

Q: A IcA B The voltage ratio in the following transformer equals to, Inc VAN/N1 Van/N2 Van/N1 Vab/N2

A: In this question, choose the correct option What is the voltage ratio of the given transformer.

Q: Simplify the circuit and solve for the All components are given or expressed in per-unit valves.…

Q: power station has this daily load curve data (a) Draw the daily load curve. (b) Draw the load…

A: Answer shown below

Q: Write an introduction about: LOAD BALANCING in 3-Phase System

A: Three-Phase System - A three-phase system is formed out of a three-phase voltage source that is…

Q: Complete the blank The load of 660 kVA with 0.62 power factor lagging, then the kW rating of the…

A: Load rating 409.2 KW

Q: TM Thermal Visayas Incorporated Power Plant generates actual load of energy for 1.352 MW supplying…

A: Here is your answer! I hope this will help you.

Q: 160 kVA 22 KV 22 KV 20/0.5 KV Generator G X= 9% Line 200 kVA 40 kVA Z- 2 + j5 2 X= 10% X= 8%…

A: Old base values of generator are 160 KVA, 22 KV. New base values are 160 KVA, 22 KV

Q: The subtransient reactance of a generator is typically much larger than the steady-state reactance.…

A: 1 ) generally the subtrasient response of a generator is larger than the steady state reactance. So…

Q: Transmission Power Lines Tutorials Tutorial n° 0: Construction of transmission power lines A Young…

A: Here is the detailed description of the electrical network layout:The electrical network starts with…

Q: 7. A power station has to meet the following load demand : 50 kW Load 4 between 10 A.M. and 6 P.M.…

A: The solution can be achieved as follows.

Q: The maximum demand of a power station is 15 MW. Annual load factor is 50% and capacity factor is…

Q: A generating station has an average demand of 15 MW. If the plant capacity factor is 50 %, what is…

A: Given, Average demand = 15 MW Plant capacity factor = 50 % = 0.50

Q: 10. Naghsh-Jahan Generation owns three generating units that have the following cost functions: Unit…

A: The generation cost is minimum when the incremental fuel cost of all the units are equal i.e.…

Q: Q1- Consider a small hydro scheme with a head of 60 m and a flow rate of 5 m³/s. If the efficiencies…

A: Given head h=60 m flow rate =5 m3/s efficiencies are ηp =0.88 ηt =0.78 ηg =0.95 Poles P=24 frequency…

Q: Classification of 1200 MWe capacity natural gas power plant

A: We need to tell about classification of 1200 MWe capacity natural gas power plant.

Q: Does the instantaneous power oscillate in the following power systems? a) Un-Balanced 3-phase AC…

A: a) In unbalanced 3-phase AC systems: The instantaneous power can oscillate because the voltage and…

Q: 5. The maximum load on the Thermal Plant of 60MW capacity is 50MW at an Annual Load Factor of 50%.…

A: Thermal power plant is generate the electricity . it is also known as a combustion power plant . it…

Q: A 25 kVA, 240 V single phase source supply the rated power at the rated voltage to a motor at 0.8…

A: As we have given : S=25 kVAV=240 Vcosϕ1=0.8cosϕ2=0.9

Q: A generating station has the following daily load cycle : Time (Hours) 0-6 6-10 10-12 12-16 16-20…

A: This question belongs to power system . It is based on the concept of load curve . By making load…

Q: * Two generators, rated at 100 MW and 400 MW, are supplying power to a network. The system frequency…

A: we need to tell the value of droop R of the 100MW generator.

Q: A hydro electric power station is used to supplement the unmet constant load demand for 2 hours and…

Q: The load in milling factory is having active and reactive power of 100 kW and 59.33 kVAr,…

A: Given Total load power Active power, Pload=100 kW Reactive power, Qload=59.33 kVAr Power factor…

Q: A power generating station has a maximum demand of 1000 MW. The annual load demand of 1000 MW. The…

A: Maximum demand=1000 MW, Annual load demand=1000 MW, Annual load factor=75%, Plant capacity…

Q: Q1. Determine the contents of the register after execution of each instruction R16, $3F R18, $01…

A: Since you have posted multiple questions, we will solve the first question for you. If you require…

Q: PAKIRAM DAM Hydroelectric station delivers a load of 30 MW for 8 hours with a head of 100 m. It…

A: in this question we need to find a volume of water needed to generate the energy consumed by load.

Q: A 450 Vdc source is connected to a 3 phase (balanced) PWM hex bridge inverter. The output phase…

Q: 5. A three-phase rectification system has a voltage ripple of 14%. If the output kVp is 150, what is…

A: Given data, Output voltage VO=150 V. Ripple voltage Vr=14 %.

Q: A power station has a daily load cycle as follows: 260 MW for 6 hrs, 200 MW for 8 hrs, 160 MW for 4…

Q: The selection of number of generating sources to meet the expected load is called as unit…

A: the selection of number of generating sources to meet the expected load is called as unit commitment

Q: Consider a building with a real power demand of 650 kW and reactive power demand of 480 KVAR.…

A: In building Power demand 650KW Reactive power 480KVAR The power factor? Capacitor rating to be…

Q: Open Cycle Natural gas power plants are having less efficiency comparing to combined cycle Power…

A: Combine cycle power plants have HRSG to increase its efficiency while the open cycle power plants ,a…

Q: Three-phase electricity is delivered to a factory 7 km from a distribution company. The factory…

Q: After a disturbance, Increase in angular separation accompanied by a decrease in power transfer will…

A: Choose the correct option Given Statment is true or false? Effect of the stablity due to…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

77. A large hydroelectric power station has
a head of 324 m and an average flow of
1370 m³/s. The reservoir has an area of
6400 km2. The available hydroelectric
3
power is
(i) 2100 MW
(ii) 5600 MW
(iii) 4350 MW
(iv) 2650 MW

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The following annual data are from a 160 MW steam turbine-generator plant. Gross generation is 780,000 MWH, net generation is 723,000 MWH, operating hours is 7,730, average load is 99.67 MW, and maximum peak load is 160 MW. Determine the load factor
Electricity demand in the Los Angeles area is 3,500 MW from 1 am to 7 am; 4,700 MW from 7 am to 12 pm; 5,900 MW from 12 pm to 9 pm; and 4,100 MW from 9 pm to 1 am. The Dalles Dam has a nameplate capacity of 1,780 MW. Assume the Dalles Dam provides all of its generated electricity to the Los Angeles area and only accounts for 25% of the Los Angeles area electricity supply at any given time. Calculate the capacity factor for the hydroelectric facility over one day, accounting for the loss in power incurred during transmission of electricity (Power loss =24 MW).
2. Determine the Ripple factor, Kr VA wt 2 2
On a particular day, the head of a dam is 85.37 m and the generators deliver 6000 MVA at a power factor of 0.9 lagging. Assuming the average turbine efficiency is 0.92 and the average generator efficiency is o.98, calculate: a. The active power output [MW] b. The reactive power supplied to the system [Mvar] c. The amount of water flowing through the turbines.
(ii) A string of suspension insulators consists of three units if the voltage across the line unit is 17.5 kV. The ratio of self-capacitance to shunt capacitance of each unit is 9:1. Determine a) V1 b) V2 c) VPh d) %String Efficiency
Help me solve this one
problem 2 1. what is the voltage provided by the building 2. What is the amount of current provided to the bullding? 3. If the building consumes 3200W of power, what is it's power factor? 4. What is the phase angle of the secondary power source in the bullding?
A power station has a maximum demand of 13590 kW. The annual load factor is 60% and plant capacity factor is 50%. Determine the reserve capacity of the plant.
5. A generating station has the following daily load cycle: Time in 0 to 6 6 to 10 10 to 12 to 16 to 20 to Hours 12 16 20 24 Load 50 60 70 60 80 50 (MW) Draw the load curve and Estimate: i. Maximum Load ii. Units generated per day iii. Average Load iv. Load Factor