HW2: The structure shown in Fig.2, is supported by rollers at A and B and fixed at C.(a) Use a suitable scale to construct the influence line diagrams for VEL, VGL and MF for the maingirder.(b) Compute the maximum reaction that can be developed at support A due to a concentrated live load( Pu = 20 kN ) and a uniform live load ( wLL = 6 kN/m ).B.2 m2 m2 m2 m2 m2 m2 m4 m2mFig.2

Given structure is supported by rollers at A and B and fixed at C. Given problem has been solved…

Answered: HW2: The structure shown in Fig.2, is…

HW2: The structure shown in Fig.2, is supported by rollers at A and B and fixed at C. (a) Use a suitable scale to construct the influence line diagrams for VEL, VGL and MF for the main girder.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in each of the members located to the left of FG for the scissors roof truss shown. State whether each member is in tension or compression.
IDENTIFY THE ZFM ZERO FORCE MEMBERS
For the truss given below: 4 KN 3KN 5m č 5m E G 5m 5m The reaction at Ay is | kN (two decimal places) The reaction at Hx is kN (two decimal places) The reaction at Hy is kN (two decimal places) Internal force BD is kN. (+ for tension, - for compression , two decimal places) Internal force BE is kN (+ for tension, - for compression , two decimal places) Internal force CE is kN (+ for tension, - for compression , two decimal places)
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
In the truss shown in Figure. Determine the force member at DE. * 400 kN 800 kN 6 m 3 m F 3 m 6 m E 6 m 200 kN 200 kN 1440 KN tension O 1440 KN compression 200 KN tension None of the above O 200 KN compression
Question 2) Identify the zero-force members in each truss. E MA 3 m D A A 800 N H 3 m 30⁰ G B 3 m (a) F 3 m 2 m B 2 m (b) C 2 m E D 4 m 500 N 700 N
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
MULTIPLE CHOICES AND SHOW YOUR COMPLETE SOLUTION: 2. Draw the influence line diagram of the given bridge truss system below for its member BC and HI if the loaded chord is member Cl? a. The maximum positive or negative ordinate for the ILD of member BC.2 o -1.2 UNITS o 1.2 UNITS o -1.04 UNITS o 1.04 UNITS b. The maximum positive or negative ordinate for the ILD of member Hl. ? o -1.2 UNITS o 1.2 UNITS o 1.04 UNITS o 1.05 UNITS c. If the bridge truss system is carrying a uniform deadload of 10 kn/m and a moving live load of 13 kn/m with two concentrated loads of 75 kn and 50 kn that is 2m apart. Determine the equivalent bar force for member BC and indicate whether it is in compression or tension. o -558 KN, C o 558 KN, T o 585 KN, T o -585 KN, C G K L 2m 4m A H 6 @ 5m= 30m
I need the answer as soon as possible
Include fbd
will thumbs up if correct!