How much would the handle rotate door was opened 5 inches

Q: ind the global stiffness matrix, displacement at node 1&2, reaction forces at 1&4, and force in…

A:

Q: finite element method If the nodal displacement for the element in figure (d) question no 1 is…

A: Given: Let us consider the given data, uiviujvjukvk=221031×10-3 mm To find: The displacement at 1,3.

Q: are unstretched/uncompressed, the maximum vertical velocity can be is 1 m/s. What is the minimum…

A:

Q: Find stiffness global displacement at node 1&2, reaction forces at 1&4, and force in spring for the…

A: Stiffness Stiffness is the extent to which an object resists deformation in response to an applied…

Q: (2) MODEL THE VELOCITY OF THE WATER SKIER SHOWN BELOW (a) IDENTIFY THE IN PUT AND OUTPUT OF THE…

A: it is asked to model the water skier

Q: Q.1 Develop an analytical reasoning to prove that the mechanism as shown in Figure.1 have mobility.…

A: To determine:To calculate the mobility

Q: Given dĴ 9 D = 400mm T = 300k N'm Inclined plane 0=60 d = 300mm Imax F = 1.5MN 1) Draw a square…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Kinetically how many degrees of freedom are required to model the system shown in Figure (7)? Also,…

A:

Q: A 68 kg mass is supported by the three springs as shown. The initial displacement is 15 cm downward…

A: MassEquivalent spring constant

Q: Q2-Find (meg) & (Keq) for the mechanism shown in fig (1), with respect to the displacement (x).

A: Given : To find: Meq and Keq

Q: (25) Find the transfer function, G(s) = 04(8)/T(s)for the rotational system shown in the figure. T)…

A:

Q: Classify the structures for Stability and determinacy , if unstable state why, if indeterminate…

A:

Q: 20 32 1,5 6 Given data: Moment of inertia of the cross section - | Material modulus of elasticity -…

A: given data: E=2.05*108KN/m2I=2.083*10-3m4A=0.10m2 R1=reaction force at point AR2=reaction force at…

Q: Consider the following spring system. C2 with spring constants c= m2 225

A:

Q: Calculate elastic compliance constants (S's) related to C's in the following matrix. [C11 C12 C13]…

A: Given data: Stiffness tensor, C = C11C12C13C21C22C23C31C32C33 To find: corresponding elastic…

Q: 3. The simply supported beam in the Figure supports P concentrated force. Find the reactions on the…

A: Given

Q: Fs For the spring assemblage shown below Figure, obtain (a) the global stiffness matrix, (b) the…

A:

Q: Section of a culvert is shown in the figure. Compute the moment of Inertia about the hori- zontal…

A: The given area can be divided into two 3 shapes 2 triangles, 1 rectangle and a semicircle as shown…

Q: For the mechanisms pictured below: perform displacement analysis both graphically and analytically:

A:

Q: Note: Lagrange's approach is recommended. P₂(t) k₁ k₂ ww P₁(t) k₂ m₂ k6 www P3(t) k₂ www m3www…

A: For solution refer below images.

Q: 0 2. As a traffic engineer, you have been asked to investigate the dynamic response of the road sign…

A:

Q: Give an example problem with this topic:Dynamic Equilibrium in Translation (Analysis as a Rigid…

A:

Q: Figure P3-41 3-41 For the insulated corner section shown in Figure P3-41, derive an expression for…

A:

Q: Consider the following spring system. Assume down is the positive direction. Write the stiffness…

A:

Q: a) Determine the system element matrix for the Laplace equation for each discretization. b)…

A: From above diagram, σr=230 MPaE = 165 GPa uV=σr22E=(230×106)22×165=160.3 KJ/m3 Modulus of resilena =…

Q: The electro-mechanical system shown below consists of an electric motor with input voltage V which…

A: To find:-the governing differential equations of motion for this electro-mechanical system in terms…

Q: F2-1. Determine the magnitude of the resultant force acting on the screweye and its direction…

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: -20kN 8. A steel bar ABCD 4 m long is subjected to force as shown in figure below. Find the…

A: Answer: The total elongation of the bar is 1.7507 mm.

Q: The kinematic chain shown in the figure is a O Mechanism with two degree of freedom Structure O…

A:

Q: Q8 (a). Find all the stable structure(s) as shown in Figure 8a. 材 V V (a) (b) (c) (d) Figure 8a

A:

Q: For the simple pendulum shown in the figure, write the governing equation in s-domain. Assume small…

A: Given:To find:Governing equation in s domain

Q: . You have been asked to select the best material for redesigning a walking stick (Figure Q4 (a)).…

A: Given question: We have to select the best material for redesigning a walking stick. It has fixed…

Q: do the question by the concepts of statics and mention

A: Draw the free body diagram at point C as follows.

Solidification of metals

The term solidification indicates the conversion of material from the state of liquid to the state of solid. The solid-state is more compact and rigid than liquid, and the solidification indicates the transformation of material from a random state to a more compact and crystalline form. The point at which dendrite formation in liquid starts taking place is referred to as the solidification point.