1. The frame, anvil and base of the forging hammer, shown in Figure 1(a), have a total mass of m. The support elastic pad has a stiffness of k. If the force applied by the hammer is given by Figure (b), find the response of the anvil. H F(1) -#-time m Base Hammer -Frame Anvil Fu Lump Funk Furt Elastic pad, k F(1) Fo

1. The frame, anvil and base of the forging hammer, shown in Figure 1(a), have a total mass of m. The support elastic pad has a stiffness of k. If the force applied by the hammer is given by Figure (b), find the response of the anvil. H F(1) -#-time m Base Hammer -Frame Anvil Fu Lump Funk Furt Elastic pad, k F(1) Fo

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

FUNDAMENTALS OF MECHANICAL VIBRATION (2nd Ed) Graham Kelly How did it reach to this answer 5.47 Derive the stiffness matrix for the system in the figure using the indicated generalized coordinates and stiffness influence coefficients
(machine dynamıc) Mass M is attached to the end of the rod of length L with mass m given in the figure on the right and it is connected to a fixed support with a spring with a coefficient of k.a- Obtain the expression that gives the natural frequency of the system for the situation in the figure.b- Explain how the natural frequency of the system is affected if the spring coefficient increases and/or decreases as 0.5k, 2k, 5k.
A mass of 0,8 kg is suspended by a spring of stiffness 215.6 N/mn as shown in figure. Find the natural frequency of the spring. S1 O a. 14.10 O b. 10.80 O C. 15.85 O d. 2.61
Crankshaft A crank of radius r rotates with an angular frequency w. It is connected to a piston by a connecting rod of length L (see figure). The acceleration of the piston varies with the position of the crank according to the function r cos 20 a(0) = wr( cos 0 + L For fixed w, L, and r, find the values of 0, with 0 = 0 = 27, for which the acceleration of the piston is a maximum and minimum. Crank Connecting rod Piston a
5. A rod of length L, Young's modulus E, cross-sectional area A and mass density p is installed as shown. Suppose m = pAL and kL / EA =1. Find the equations of motion Open Question m www f(t) x=0 x = L/2 x= L
I Review Use a block-and-spring model like that shown in the figure, but suspended from a vertical position and subjected to a periodic support displacement 8 = 8psinwnt, determine Express your answer as an equation in terms of some or all of the variables y, a (a = y), ki, m, wn (wn = V). wn, t, and on. the equation of motion for the system, and obtain its general solution. Assume positive displacement is downward. (Figure 1) Va AZo| t vec k la+ m k sin @, t m That's not quite right. Please check your formatting and try again. No credit lost. Try again. Submit Previous Answers Request Answer Part B Obtain the general solution of the above equation. Figure 1 of 1 Express your answer in terms of some or all of the variables A, B, t, k, m, wn (Wn = 1/), 80, and wo. V ΑΣφ vec Equilibrium position A sin (@,1) +B cos (@,1) sin (@,) mw,“ 1- k y = Bd8 = 8, sin d Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining
2- Derive the rule-of-mixtures expression for the composite extensional modulus E₁ assuming the existence of an interphase region. The starting point for the derivation would be the model shown below. For simplicity, assume the interphase, like the matrix, is isotropic with modulus E¹. With an interphase region there is a volume fraction associated with the interphase (i.e.,V;). For this situation: vf + vm + vi = 1 H |w²||wm|
An undamped spring/mass system, in which m = 8 slugs and the spring constant k = 16 lb/ft has a driving force f(t) = t^pi*t on [0,pi] Extend f(t) into the negative t-axis to obtain an odd function. Find the particular solution ??(?). (Note: f(t) is given as half of the period, p = π.)
For the simple pendulum shown in the figure, write the governing equation in s-domain. Assume small angles and linearize your model. Initial conditions are zero. Explain each step clearly. - 0(1) L, length m, mass
Figure below shows an aircraft fighter. The wing of the aircraft may be modelled as a clamped wing with two lump masses at its centre and tip. The two masses represent the mass of the wing and the missiles. The equivalent model shown in the figure is used to estimate the first two natural frequencies of the wing and therefore the fuselage can be assumed rigid. 24EI If m1 = am, m2 = bm and bending stiffnesses of the beams are k where a = 6.3005 and b = 13 %3D 5.2174 and if w1 and w2 are the first and second natural frequencies of the system, w2/w1 is: x, (t) x2(t) EI m, EI (m,) 1/2 1/2 3.4053 4.9188 2.5225 1.3621 1.8414
Q.1 The system shown below consists of a block of mass m and a cylinder of mass 2m. The block and the cylinder are joined by pulley arrangement as show. The coordinates x and y are dependent in which x = 2y. Use m= 2 kg. The angle 0 is any value between 0 and 90°. If the cylinder is pushed downward 20 mm and released a) find the subsequent response of the block, x(1) b) find the displacement and velocity of the block at t = 1 s. The specific value of k is given in separate excel sheet. K=1985 2m IT, x = 2y
2. Find the natural frequency of vibration of a spring-mass system arranged on an inclined plane, as shown in figure below. (10 points) m