How much deformation does a mass of 1 kg falling from a height of 6 meters cause to the built-in beam with a length of 1.5 meters and a cross-sectional area of 40x60mm2? Please choose one: a. 35 b. 25 c. 15 D. 30 to. 20

Q: 01: A cantilever 5 m long carries a niformly distributed vertical load 80 N per meter from C from H,…

A:

Q: A beam (AB) is supported by a roller at B and a pin at A. It is subjected to the following uniform…

A:

Q: Determine the resultant internal loading acting on the cross section at C of the cantilevered beam…

A: Consider the free-body diagram of part CD. Apply force equilibrium in a horizontal direction.

Q: Which of the following method the forecast is done by taking average of all data.

A: We are to declare which forecasting method includes all data points

Q: A beam is subjected to equal 12.3 kip-ft bending moments. Assume t - t2- tw- 2 in., d- 13 in., b; -…

A:

Q: For the given state of plane strain, use Mohr's circle to determine the state of plane strain…

A:

Q: The internal bending moment at point B (in N.M) is 200 N/m A IB – 3 m- -3 m-

A: Let's mark the points B, C, D, E, G as shown in below figure. Let's make a section S-S at B to find…

Q: If a force of 100 pounds is required to push a block upward an inclined purface 10 with the…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 1.61. L- The beam of length 5.2 (m) and cross section base 0.20 (m) and height 0.19 (m) shown is…

A: Given

Q: 11.2 kN/m A B 2.8 m 3.1 m Fig. Q1 Note: not drawn to scale

A: To determine the reactions at A and B and to draw the hear force diagram.

Q: U.092.0 A force of 500 N is applied on a rigid bar as shown in the figure. The moment of F about…

A:

Q: ( Find the Resultant Force when ( R_x = 60.8 Ib , R_y = 192.4 Ib .A 203lb

A: Given:Rx=60.8 lbRy=192.4 lb

Q: A uniform 30-lb beam, 10 feet long is carried by two men A and B, one at each end of the beam. a) If…

A: Given Data Weight of uniform beam WD=30lbs Length of beam l=10ft Weight of load, Wl=50lbs Force…

Q: A truck and trailer combination has wheel loads of 6 kN, 9 kN. and 12 kN, separated at distances 3m…

A:

Q: Q2: Draw the S.F. and B.M. diagrams for the beam which is loaded as shown in Fig. Determine the…

A: To find:- SFD and BMD  =?  Determine point of contraflexture = ?

Q: The top of the circular table shown to the side is 1.2 meters in diameter and weighs 26 kg. If a 90…

A: Solution: Given Data: D=1.2 mm=26 kgM=90 kg   To Find: The diameter of the circular base of the…

Q: a) Determine the second moment of area (IXX) about the centroidal x-axis for the solid homogeneous…

A:

Q: Q) Draw the S.F. and B.M. diagrams for the beam loaded as shown in Figure, inserting principal…

A: Let reactions at A and D are RA and RD respectively. Consider upward forces as (+)ve and downward…

Q: 5. A person pulls on a rope with a force of 100 lbs as shown below. What is the moment about point A…

A:

Q: 10 ksi, oy -4 ksi, and o, = 8 ksi. Using E = The normal stresses at a point in a steel member are o,…

A: Answer: The normal strain along z is (0.2138 × 10-3) in/in.

Q: Q. Sketch the shear force and bending moment diagrams, inserting the principal numerical values for…

A: Given: Sketch the shear force and bending moment diagrams.

Q: A beam ABCDE is 5 m in length and loaded as shown in Fig.3. Draw the S.F. and B.M. diagrams for the…

A:

Q: The ball ( D) has a mass of ( 15 kg ). If a force of ( F = 80 N ) is applied horizontally to the…

A: Apply the conditions of equilibrium ∑Fx=0100-FABcosθ=0FAB=100cosθ∑Fy=0FABsinθ-196.2=0…

Q: A9B) The resultant force of P1 and P2 is 40 N. If the moments of P1 and P2 are (-30 N.m) and 50 N.m,…

A:

Q: A force F of 10 N is applied in the direction indicated, per meter depth (into page). The 300 mm…

A: Data given  h = 4 mm  b = 300 mm  F = 10 N

Q: A 3 inch by 4 inch rectangular bolt pattern is used in a bolted connection carrying a vertical load…

A:

Q: a concentrated for nt of 900 N.m. as n ction forco at th

A: reaction force at b is required

Q: 237. A spring requires 5 J to stretch the spring from 8 cm to 12 cm, and an additional 4 J to…

A: According to the given data a=8cm  b=12cm     Spring required 5J to Stretch from 8 to 12  c=12cm…

Q: 4.5 ft 80.5 O 80 O 90 o The crate weight is 270 lb. The minimum force p for tipping is 75.2 150 150…

A:

Q: A spherical balloon 6 m in diameter is filled with gas weighing 5 N/m³. If the specific weight of…

A:

Q: The solution must be in Handwritten format including diagrams. Please don't give random solutions.

A: Part 2: Approach to solving the question:To find the maximum internal bending moment in the beam, we…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.