Catherine is planning to build a stage. Her brother bought beams with cross section at hand as shown in Fig.Q2. The maximum moment acting on a beam is 180 kNm. She has a choice of either using Birch wood which has both tensile and compressive strength of 4 GRą or Brazil Nut which has both tensile and compressive strength of 5 GPa. Determine through calculation whether this cross section would be applicable.

Catherine is planning to build a stage. Her brother bought beams with cross section at hand as shown in Fig.Q2. The maximum moment acting on a beam is 180 kNm. She has a choice of either using Birch wood which has both tensile and compressive strength of 4 GRą or Brazil Nut which has both tensile and compressive strength of 5 GPa. Determine through calculation whether this cross section would be applicable.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: Check the adequacy of the beam shown in Fig (1-a) with section shown in Fig (1-b) at section B-B only. f 28 MPa, f, = 420 MPa 800 I 150 4012 640 + 10 stirrups W =200KN /m B 4025 150 150 iB Section B-B 2m 6m 2m Fig.(1-a) Fig.(1-b)
A bracket with a basic shape cross-section is loaded as shown in Fig. Q3. Determine the following: Q3 a) The axial stress in the section X-X b) The tensile and compressive bending stress at the outer most beam fibre in the section X-X
What is the purpose of the buckling practice and how does the effective length (Le) influence the tests? please reply quickly. I WILL RATE IT
need correct and urgent
EXAMPLE No. 2 The laminated beam shown supports a uniform load of 12 kN/m. If the beam is to have a height to width ratio of 1.5, determine the smallest width. Gallow-9 MPa, tallew = 0.6 MPa. Neglect the weight of the beam. 12 kN/m B 1.5b A 3 m 1m
sovle the question given in the pic.
If the "I" value of beam cross section is 6,400,000 mm and the maximum distance from the neutral axis of the cross section to the top and bottom edges of the beam cross section is 139 mm, what is the section modulus of the beam? Note: Give your answer in mm3 Note: Do NOT include units in your answer. Answer:
Complete free body diagram + explanation required
90 mm, 90 mm 170 mm M 50 mm 37.5 mm Figure Q1 (a)
A cantilever beam, 80 mm wide by 240 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1100 N/m at the wall. Compute the magnitude of the maximum flexural stress. Answer must be in MPa.
2. A Pelton wheel is working under a head of 180 m with a discharge of 0.8 m3 /s. The following data are available for the turbine: Coefficient of velocity = 0.985 Angle of deflection of jet = 165° Speed ratio 0.46 Relative velocity at exit = Relative velocity at inlet Jet ratio 12 Compute the (a) hydraulic efficiency, (b) velocity of whirl at inlet and outlet, and (c) mean bucket speed. Assume zero frictional loss in the bucket.
Q3/ Fig. 3 shows a cost iron bracket of cross-section of I-form. Determine the maximum bending moment that should be imposed on this section if the tensile stress in the top flange is not to exceed 40 MN/m² What is then the value of the compressive stress in the bottom flange? Fig. 3 40 mm 200 mm mm 200 mm T 40 mm 120 mm