8.1 IncorrectCompression member AB is used to hold up the 250 x 340-mm rectangular plate. If the compressive force in the member is 315 N forthe position shown, determine the magnitude of the projection of this force (as it acts at point A) along diagonal OC.250[28%280225115Answer: Foc i -152.95CB70Dimensions in millimetersN X IncorrectCompression member AB is used to hold up the 250 x 340-mm rectangular plate. If the compressive force in the member is 315 N forthe position shown, determine the magnitude of the projection of this force (as it acts at point A) along diagonal OC.250[28%280225115Answer: Foc i 220.210CB70Dimensions in millimetersN

Compression member AB is used to hold up the 250 x 340-mm rectangular plate. If the compressive force in the member is 315 N for the position shown, determine the magnitude of the projection of this force (as it acts at point A) along diagonal OC. 250 28% 280 225 115 Answer: Foci -152.95 C B 70 Dimensions in millimeters N

Compression member AB is used to hold up the 250 x 340-mm rectangular plate. If the compressive force in the member is 315 N for the position shown, determine the magnitude of the projection of this force (as it acts at point A) along diagonal OC. 250 28% 280 225 115 Answer: Foci -152.95 C B 70 Dimensions in millimeters N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select All Correct Answers.
Q1. Experiments were conducted in a tension testing machine to evaluate the material properties of two metallic rods both having diameter equal to 10 mm. First rod having modulus of rigidity of the material equal to 400 tonnes/cm2 when subjected to an axial tensile force of 6 kN, the change in its diameter was observed to be 0.0018 cm. The value for the bulk modulus of the second metallic rod is same as that of the first one but modulus of elasticity 18% more. Based on the material properties calculate and compare the values of different moduli as well as Poisson's ratio for both metallic rods. Justify your answer with reasons.
Q2) Draw the sheering force and bending moment diagrams for fig2 Fig.2 112 4 kN/m 2 6 RA 3 RB
How did the final answer become kilogram?
One of the principal stresses in a two-dimensional stress system is 139 N/mm² acting on a plane A. On another plane B normal and shear stresses of 108 and 62 N/mm², respectively, act. Determine a. the angle between the planes A and B, b. the other principal stress, c. the direct stress on the plane perpendicular to plane B. Ans. (a) 26°34', (b) –16 N/mm², (c) 15 N/mm².
A mild steel material is subjected to a Brinell hardness test with an applied force of 7830 N using a hardened steel ball indentor of 10 mm and it is found that the Brinell Hardness Number as 936. Determine the surface area of indentation and indentation diameter. i) Surface Area of Indentation (in mm2) ii) Indentation Diameter (in mm) · --
3- A loaded structure with a two-dimensional stress state has the stress in the x-axis is 13.5 Mpa, in the y-axis is - 3.2 Mpa, and the shear stress in the x-y is - 4.4 Mpa. a) Write the stress transformation equations b) Calculate o and t for the inclination angle 0 between the n values 0 to 180°, in 15° increments. c) Draw the profile graph of normal stress and shear stress with e in the x-axis d) Obtain from the graph, the principal stresses o,, o,, and 2' maximum and minimum shear stresses Tmax and tmin e) Obtain from the graph the corresponding inclination angle Op1, Op2, Os1, and es2 for each of principal stresses and shear stresses, respectively
As information for the mechanic, it is desired to evaluate the variation in shear force along the length of the shaft. Therefore, what is the value of the shear force in the central section of the shaft (125 mm < x < 600 mm)? Options: a) The shear force in the central section of the shaft is 0 kN. B) The shear force in the central section of the shaft is 0.8 kN. c) The shear force in the central section of the shaft is 1.5 kN. d) The shear force in the central section of the shaft is 1.48 kN. e) The shear force in the central section of the shaft is 0.82 kN.
Plane stress at a point in a body is defined by the principal stresses, 9 o and o. On the plane of the maximum shear stress, the ratio of the normal stress to the maximum shear stress will be O a. 4.00 Ob. 5.00 O c. 1.25 O d. 2.00
3
4. As for the relationship between normal stress and shear stress, it is correct that () (A) The normal stress and shear stress on the same section are perpendicular to each other; (B) The normal stress and shear stress on different sections are perpendicular to each other; (C) The normal stress and shear stress on the same section are parallel to each other; (D) The normal stress and shear stress on different sections are parallel to each other;
What do the internal loadings in a body consist of?