how many degrees are allowed between pull points?

Q: What is clamper? Briefly explain its working.

A: We neec to tell about clamper circuit . We need to draw the circuit diagram and output waveform for…

Q: Explain insulation coordination

A: Coordination is required in electrical systems for proper functioning of the equipments. Insulation…

Q: 5) The deflecting torque of an ammeter varies as the square of the current flowing through it. If a…

A:

Q: A simplex lap wound armature has 540 conductors and carries a current of 95 amperes per armature…

A: Given:-

Q: Is this armature winding a progressive or a retro-progressive winding? 6. 10 16 3* 12 4- 6 14 North…

A: If after one round of the armature the coil falls in a slot left to its starting slot the winging is…

Q: 2. Explain electrical contact resistance. Holm model of electrical contact resistance. Contact…

A: It is asked to explain contact resistance and the Holm model of contact resistance. Also it is asked…

Q: the armature mmf can be -2 reduced by reluctance of the magnetic the circuit in the region of the…

A: The explanation is as follows.

Q: Explain the following armature winding terminologies (i)commutator Pitch (ii)Coil Side (iii)Pole…

A: The given armature winding terminologies: (i)commutator Pitch (ii)Coil Side (iii)Pole Pitch

Q: What type of Power Losses does windage loss, bearing and brush friction loss is considered? a Stray…

A: Copper losses are losses due flow of current in winding. Copper loss in DC machine occurs in both…

Q: 16. (a) What load impedance Z₁ will draw the maximum average power from the source shown in Fig.…

A: Kirchoff's Law (KCL and KVL) and Ohm's law is very important to analyze electrical circuits. As per…

Q: a. Does the slip increase as the load increases? What is the reason of this? b. What does it mean…

A: (a)  Slip :- It is the difference between the synchronous speed of the motor and the shaft rotating…

Q: How can the polarity of an electromagnet be determined if the direction of current flow is known?

A: Since we only answer one question at a time, we’ll answer the first question since the exact one…

Q: Explain the following static performance terms as applied to measument systems  1. Accuracy 2.…

A:

Q: 5. Find the fundamental period of 1+sin^2 (3t/5)n. a) 10/3 b) 5 с) Зл/5 d) None of the mentioned

A: In this question we will find fundamental time period of given discrete system....

Q: Explain how Kirchhoff's Current Law serves as the founding principle of a grounding strap.

A: KCL is a fundamental principle in electrical circuit theory that states that the total current…

Q: What happens to the reluctance of a magnetic path if its length is doubled? If the crosssectional…

A: The formula for Reluctance is: R=lμAWhere,R=Reluctancel=Length of the magnetic pathA=Cross section…

Q: Draw occ at 800 rpm At 1000 rpm And 600 rpm and air gap Field Armature emf V Armature emf V Armature…

A:

Q: Design a clamper to perform the function indicated in the given figure. Please upload your solution.

A: Clamper is a circuit which clamps the total signal above or below the reference voltage depending…

Q: Discuss the operation of non-contact torque measuring instruments

A: Non-contact torque measuring instruments are torque sensors. A type of transducer that transforms…

Q: What's the maximum percent overshoot for this system with its closed-loop poles as shown? Jo Select…

A: We need to find out overshoot for given system.

Q: Electrostatic levitation in comb-drives: Movable fingers in comb-drive actuators/sensors can…

A: According to the question, for the given figure as shown belowwe need to explain levitation happens…

Q: (10) Find the equivalent impedance in phasor form for the circuit shown in Figure 2. Given: I = 5…

A: Source current Is=5cos377t+450 A. R=1 kΩ, L = 0.8 H, C=220 mF.

Q: What is turnover torque and when occur؟

A: Turn over torque is the maximum torque that can be delivered for any motor  without losing steps. It…

Q: What is the difference between bounding and grounding?

A: The difference between bounding and grounding is given below: 1) Bonding is the lasting joining of…

Q: Discuss reversed polarity and why is it dangerous to reverse you wire connection

A: Wire connection There are three types of wire connections. They are live wire, a neutral wire, and…

Q: Explain how LVDT can be used for the measurement of displacement.

A: LVDT can be used for the measurement of displacement.