2/121 A 50-lb force is applied to the control pedal as shown. The force lies in a plane parallel to the r-z plane and is perpendicular to BC. Determine the moments of this force about point O and about the shaft OA. Аns. Мо -90.6i - 690j - 338k lb-in. MOA = -690 lb-in. 7" 6" B 15°. 8" 50 lb Problem 2/121

2/121 A 50-lb force is applied to the control pedal as shown. The force lies in a plane parallel to the r-z plane and is perpendicular to BC. Determine the moments of this force about point O and about the shaft OA. Аns. Мо -90.6i - 690j - 338k lb-in. MOA = -690 lb-in. 7" 6" B 15°. 8" 50 lb Problem 2/121

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A standard truck moves across a 25- meter span. The wheel loads are P1=36 kN and P2=142 kN separated by 4.3 m and P3=142 kN at 7.6 m from P2. Calculate the maximum moment. O 156.54 KN.m O204.16 KN.m O 259.7 KN.m O 1409.7 KN.m
Consider the magnetic circuit given in below figure with parameters: u=153 Ho, d1=9 cm, d236.2 cm, d3=7.9 cm, da=0.3 cm and N=497. Assume that all branches have the same cross-sectional area of 5 cm. Magnetic flux density is 0.1 Wb/m2 in the air gap. Based on the given configuration calculate the current I in [A] in the coil. d2 d3 d, Tolerance + 0.1 relative
3- A shunt machine connected to 250V mains has an armature resistance (including brushes) of 0.120 and the resistance of the field circuit is 1002. Find the ratio of the speed as a generator to the speed as a motor. The line current in each case being 80A 1001 W 200
H.W-3 1- Why the capacity of SG is taken in kVA and for IM is taken in kW? 2- Explain the effect of changing the load (inductive-capacitive- resistive) on SG terminal voltage? 3- Why the magnetization curve of SG is similar to the B-H curve of armature steel core? 4-Write a short report about Blondel two-axis theory for SG?
3. The torque applied to move the pointer is 279.8x10-6 N/m-¹ and it creates the 0.859 Wbm-2 magnetic field density. The effective depth of the coil has 5.5 cm x 0.125 m with voltage and power consumed by the meter are 21.9V and 286.9mW. If so then, i) calculate the total torque required to stop the pointer over the scale, ii) calculate the total current flow through the coil and resistance, iii) calculate the number of turns of the coil.
Can you answer the question?
Problem 3: Calculate the Y-parameters matrix for the circuit shown below: 6Ω 6Ω ΖΩ ΖΩ
A P KN Refer to the figure. d₁ 0.9 m Force P is 60 kN and each force Q is 125 kN. Q KN B Add your answer Integer, decimal, or E notation allowed Q KN The diameter d₁ = 30 mm and diameter d₂ = 50 mm. d₂ 1.2 m What is the normal stress in rod BC in MPa? Round to the nearest integer and enter the magnitude only. C
Q5- Calculate the value of the current "I" needed to setup airgap flux of 6 mwb. The magnetic circuit is laminated with 0.9 iron factor and H-1200. Take a, 2000 mm² and a4000 mm². 35 mm 35 mm 35 mm -+ 50 mm 1 mm 1000 turns 80 mm 50 mm 35 mm az
3. The torque applied to move the pointer is 355.6x10-6 N/m-1 and it creates the 0.598 Wbm-2 magnetic field density. The effective depth of the coil has 5.5 cm x 0.131 m with voltage and power consumed by the meter are 26.5V and 288.3mW. If so then, i) calculate the total torque required to stop the pointer over the scale, ii) calculate the total current flow through the coil and resistance, iii) calculate the number of turns of the coil.
79 84 86 help plz i need to pass
× 4:03 K s.eng.ruh.ac.lk □ Û 8. Figure 4 shows the core of a simple dc motor. The magnetization curve for the metal in this core is given by Figure 5 and Figure 6. Assume that the cross-sectional area of each air gap is 18 cm² and that the width of each air gap is 0.05 cm. The effective diameter of the rotor core is 4 cm. L It is desired to build a machine with as great a flux density as possible while avoiding excessive saturation in the core. What would be a reasonable maximum flux density for this core? ii. What would be the total flux in the core at the flux density of part (i)? iii. The maximum possible field current for this machine is I A. Select a reasonable number of turns of wire to provide the desired flux density while not exceeding the maximum available current. Flux Density, B (T) 2.8 སྤྲ ཤཱ ཀ ཀཱ བྷ ཀ ཡཱཾ བ ་ 1.2 1.0 0.4 0.2 4-48cm Figure 4 0 10 20 30 40 50 100 → Depth 4 cm -0.05 cm 200 300 500 1000 2000 Magnetizing Intensity, H (A.turns/m) Figure 5 Magnetization curve…