How many address input, data input lines ana data output lines are required for a 16K x 12 memory? A certain semiconductor memory chip is specified as 2K x8. How many words can be stored on this chip? What is the word size?

How many address input, data input lines ana data output lines are required for a 16K x 12 memory? A certain semiconductor memory chip is specified as 2K x8. How many words can be stored on this chip? What is the word size?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the ROM memory chip shown, find the capacity (including units) . organization: is this memory volatile or non-volatile? (circle one) D7 DO A B IC GZA G28 G1 A16 A17 A18 YO Y1 Y2 0 Y30 Y4 AD ROM A15 VocVpp MEMR OE CE Each Y controls A19- Y50 Y7 Given the ROM memory chip and decoder circuit below (the decoder used is the 74LS138) is used in a system with a 20-bit address bus, find the address range (in hex) the chip will respond to: upper one block lower
6. Given the number 0XA0BOCODOE0F0, a. How many bytes for this number b. How many bits for this number c. Store in 8-bit computer with little endian system, and the starting address is 0x123, please show thedata memory map d. Store in 8-bit computer with big endian system, and the starting address is 0x123, please show the data memory map
a) 16 pieces of 32Kx8 SRAM are connected to 8088 to address the 00000H-7FFFFH memory region. This circuit uses 3 separate decoders to select the appropriate memory regions. Draw this circuit showing the address, data and control connections. (Do not buffering.) b) 8 pieces of 32Kx8 SRAM will be connected to the circuit in a way to form the address space C0000H-FFFFFH. Accordingly, draw the new circuit to be added to the above circuit. (You can use additional decoder or gate circuit.)
Question 4 a) Show the output waveform of a NAND gate with the inputs A, B, and C indicated in the figure below. A C b) A cache has been designed such that it has 1024 lines, with each line or block containing 8 words. Determine the line number, tag, and word position for the 20-bit address 3E9D216 using the direct mapping method. c) The table below represents 10 lines from a 256 line cache that uses direct mapping with a block size of 4 words. Identify the address of the shaded data (8C16). 3 Line# |Tag Word 00 Word 01 Word 10 Word 11 10 110101 12 34 56 78 01010154 l000111 29 32 6A D3 8C A2 BC 12 ED F3 3 001100 33 2C C8 14 110011 9A D8 FO
A multiplexer a.Takes a single data input and routes it to one of several outputs b.Selects from many data sources c.converts a binary code input to a single output d.converts a single input to a binary code
A two-way set associative cache memory uses blocks of four words. The cache can accommodate a total of 512 words from main memory. The main memory size is 4096 x 16 bits. Formulate all information required to construct the cache memory. How many bits are there in TAG, BLOCK (row) and WORD (column) fields?
Given the memory content below, fill in the table below with the register values after the execution of 3 instructions starting at instruction at address 589. Consider the initial values PC=589 and AC=0006. (all values are in Hexadecimal). address Content 13C 025A 25A 0231 589 113C 58A 7200 58B 7020 Note that you need to fill 4 digits for AC, 3 for PC, and 1 for E. AC (in Hex)= EEBE PC (in Hex)= 58C E=
e t n Se 11 • REC Assume a very simple microprocessor with 12 address lines with which we wish to implement only a quarter of the largest addressable memory using the same 512x8 memory chips. Physical memory must be placed on the upper half of the memory map. a. What is the size of the memory implemented? b. How many memory chips would be needed to implement this memory space? c. How many lines would each chip require to address its internal memory cells? d. How many lines would be required to select each chip e. Draw a simplified partial address decoding table listing all the memory chips as (MEMO, MEM1, MEM 2. etc.) and show the lines used for address decoding (chip selection) and those used to address internal memory cells. Fill the table appropriately with 1's, O's and X's (don't cares). 4. Consider the data definition statement below. num1 WORD 192AH array1 WORD OA23BH, 7EA1H, 5BEFH a. Write assembly code to compute the size of the data label array1. b. Write assembly code to add…
An LD instruction, located at x4008, loads register R4 with the content of a memory location. What is the lowest address that can be read? O X3F08 O X4F09 O X4F0B O X3F09 O x4109
Consider the following assembly program MOV CX, 1100H DLY: SUBS CX, CX, #1 NOP BNE DLY NXT: --- (a) How many times does the BNE DLY instruction get executed? (b) Change the first line of the program so that BNE DLY is executed 34 times (c) Change the second line of the program so that BNE DLY is executed 34 times, while the fist line stays unchanged (MOV CX, 1100H)
A system with 16 bits address bus can access 2^16 memory space. Estimate the size of each memory IC that will require for a memory module if the number of bits required for the chip select is 8