How is it used in 21. Injection of ethane, propane, butane, pentane, hexane, hep- tane, and octane on a squalene column under isothermal conditions gives retention times of 3.51, 4.98, 7.30, 11.00, 16.85, 26.12, and 40.8 min, respectively. Air, which is nonre- tained, elutes at 1.00 min. An injection of benzene, butanol, nitropropane, pyridine, and 2-pentanone under the same conditions gives retention times of 20.00, 6.50, 4.10, 10.05, and 10.35 min. What are the Kováts retention indexes for benzene, butanol, nitropropane, pyridine, and 2-pentanone

How is it used in 21. Injection of ethane, propane, butane, pentane, hexane, hep- tane, and octane on a squalene column under isothermal conditions gives retention times of 3.51, 4.98, 7.30, 11.00, 16.85, 26.12, and 40.8 min, respectively. Air, which is nonre- tained, elutes at 1.00 min. An injection of benzene, butanol, nitropropane, pyridine, and 2-pentanone under the same conditions gives retention times of 20.00, 6.50, 4.10, 10.05, and 10.35 min. What are the Kováts retention indexes for benzene, butanol, nitropropane, pyridine, and 2-pentanone

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Aa.18.
You prepare a buffer solution from 10.0 mL of 0.100 M (3-morpholinopropane-1-sulfonic acid) and 10.0 mL MOPS of 0.089 M NaOH. Next, you add 1.00 mL of 6.13 x 10-5 M lidocaine to this mixture. Denoting lidocaine as L, calculate the fraction of lidocaine present in the form LH+. .545 fraction as LH+ = Incorrect MOPS K₁ = 6.3 x 10-8 CH3 NH arc CH3 Lidocaine Kb = 8.7 x 10-7
1) The question screenshot has been attached down below.
In a 1.10 m gas-liquid chromatographic column the following results were obtained: air, 18.0 s; methyl acetate, 1.98 min.; methyl propionate, 2.24 min; methyl n-butyrate, 7.93 min. The base widths of the last three peaks were: 0.19; 0.23 and 0.79 min, respectively. Calculate the theoretical number of plates and the plate height of each column.
5
Carboxylic acids, including fatty acids and benzoic acids, are often present inboth municipal and industrial effluents. Describe a sample preparationcombined with GC method for identification and determination of carboxylicacids in raw wastewater at ppb (µg L-1) level. Point out a suitable samplepreparation technique and GC conditions in details and give justifications foryour choice
It has been noticed that adulteration of palm oil with carcinogenic dyes are on the rise. Use your knowledge in analytical processes to systematically process adultrated palm oil to gain qualitative and quantitative information spectroscopically about any added toxic.Explain also the basis for your protocol of choice
Transfer 3-4 drops or a pinch of the test compound (Acetanilide) to 3 ml of the solvents, 5% NaOH and 5% HCL Shake the mixture thoroughly. The time required for the solute to dissolve in the solvent should not be more than 2 minutes. Indicate with (+) or (-) if the test compound is soluble or insoluble in the solvent. Is Acetanilide solube or insolube in 5% NaOH? _______ Is Acetanilde soluble or insolube in 5% HCL? _______
A 1.00 mL aliquot of stock Na2S2O3 solution (0.0675 M) was diluted to 100. 0 mL. This was used to titrate a 50.00 mL water sample for Winkler Determination of D.O. The sample required 8.55 mL of the titrant. Compute for the ppm O2 (molar mass of O2 = 32.00).
1. A certain amount of methyl was hydrolysed in the presence of an excess of 0.05 mol dm^-3 hydrochloric acid at 250C. When 25 cm^3 aliquots of reaction mixture were removed and titrated with NaOH solution, the volume V of alkali required for neutralisation after time t were as follows. t/ min 21 75 119 V/ cm^3 24.4 Determine reaction order with substitution methods and graphical methods and calculate the rate constant and half time this reaction. (Avery, 32) 25.8 29.3 31.7 47.2
Benzoic acid is not very soluble in water and has a much stronger affinity for organic solvents. Considering the reaction below, which of the following best describes what will happen when a base is added to a liquid-liquid extraction system containing water, benzoic acid, and an organic solvent like hexane? Please note that states of matter have been omitted from the reaction. Assume excess NaOH is added. + Na +H2O HO. + N2OH Benzoic Acid Sodium benzoate O Sodium hydroxide will be in the organic layer. O Sodium benzoate will be in the organic layer. O Sodium benzoate will be in the aqueous layer. O Benzoic acid will be in the aqueous layer. O Water will be in the organic layer.
In a reaction between sodium thiosulfate and n-propyl bromide at 37°C, the amount of unreacted thiosufate was measured by titration with 1₂. Data for the 12 titre in cm³ of 0.02572 N 12 per 10.02 cm³ sample of reaction mixture is given below. t (sec) 0 1110 2010 3192 5052 7380 11232 78840 12 (titre) Determine the magnitude of the rate constant. Type in your 37.63 35.20 33.63 31.90 29.80 28.04 26.01 22.24