hooks Gand H. 0.35 m

Q: 10 Fig. (6) 8 MPa

A: Given Dataσx=8MPaθ=24°

Q: Distinguish between simple and indirect shear stress?

A: Simple shear stress also known as direct shear stress is the shear stress developed due to a…

Q: How can we determine the maximum displacement?

A: The expression for the displacement of the simple harmonic motion is given by, Here, x is the…

Q: What does it mean to be an independent slip system?

A: Slip system: It is a combination of slip planes along which the probability of deformation is…

Q: State the formula for: - the actual mechanical advantage (AMA) of wedge; - the ideal mechanical…

A:

Q: Give an example of a flexure formula?

A: The flexure formula is also known as the flexure bending equation and is defined as; Where, M is…

Q: When does a vibrating motion occurs?

A: Vibratory motion: Vibratory motion is defined as the type of motion in which a particle moves to…

Q: What are valid reasons for adding Yttrium to the zirconia in the Thermal Barrier Coating (TBC) in a…

A: The yttrium stabilized zirconium has very low conductivity and remains stable at very high…

Q: 16 A steering rack of a car must be able to withstand large amounts of sudden impact forces without…

A: Ductility: When the tensile load is applied on the material then the material fails after a…

Q: Explain the Navfac (1982) Correlation for Sub grade Reaction Modulus ?

A: Modulus of subgrade reaction is outlined because the pressure per unit deformation of the subgrade…

Q: How does polishing a connecting rod in a high speed internal combustion engine help to reduce the…

A: Connecting rod used to transmit the compressive and tensile load transmitted by crankshaft.

Q: -0.749 diom -0.561 diam -24 UNF-2A-

A: Based on the information provided, there are two components that failed: the M24 engine mounting…

Q: Differentiate between dry friction and internal friction ?

A: Friction: Friction is the force resisting the relative motion of solid surfaces, fluid layers, and…

Q: Perform a FMEA analysis for the air fryer developed . Consider different failure modes as applicable…

A: To analyse: FMEA for the air fryer developed.

Q: How did you calculate the local skin friction coefficient

A: The local skin friction coefficient is the component of the drag profile which is the resistant…

Q: The theoretical failure strength is significantly higher than the empirical failure strength of…

A: Deformation in the polycrystal grains is similar to that of single crystal. The mechanism of the…

Q: Application of, Solid, liquid , semi- solid and gaseous lubrication in engineering application

A: Solid lubricant are available in form of powder which acts as an anti-friction coating agent. It…

Q: When can the Hooke's law be applied?

A: Hooks law: It is a law which states a relation between strain and stress up to a limit. this limit…

Q: A & D reactions? 6 kips/ft AB 9'-

A:

Q: When does the impact occur?

A: Impact: It the force that is applied to the specimen or object from a certain height. These are…

Q: Stresses applied to plastically deform the metal are usually compressive. O F

A: To get the material plastically deformed it is necessary that stresses are applied beyond the…

Q: What does eccentric impact refers to?

A:

Q: What Fundamental problems occur in finding the resultant Internal normal force?

A: The resultant internal force is defined as the force, which is the result of resisting forces in the…

Q: The collar A, having a mass of 0.75 kg is attached to a spring having a stiffness of k = 260 N/m.…

A: Given data  Mass of collar = 0.75 kg Spring constant = 260 N/m Find the speed of collar and normal…

Q: Why are the young modulus not used?

A: Tension in the wire is givenAnd working tensile strength is also gievn

Q: hat is the reaction force?

A: To define what is a reaction force.

Q: What is impingement velocity?

A: Flow impingement occurs when the approach channels flow directly into a bank line at large acute…

Q: The springs in are shown in the equilibrium 3 m 4 m 3 m kAC= 20 N/m kAn 30 N/m www KAD 40 N/m…

A:

Q: 57. In gas welding process, rubber is used as preferred material for hoses. Select one: True False

A:

Q: What are the ultimate strengths in tension and in Compression for ASTM A48 Grade 40 cast iron?

A: Given data  What is the ultimate strength in tension and compression for ASTM A48 Grade 40

Q: How can the torsion formula be applied?

A: Torsion is the moment load applied on the beam or shaft about the polar axis of the beam. When a…

Q: How does the Deformation of a body occur?

A: Deformation: Whenever a body is subjected to a change in its shape size from its original shape and…

Q: Can the Shear stres also occur during axial loading?

A:

Q: Q.Define the slip and show the effect of slip on velocity ratio.

A: SLIP Pulleys (driver/driven) and the band are defined as inadequate frictional grip. Slip is the…

Q: When does the magnitude of stress increase?

A: When a body undergoes deformation under normal or shear forces/loads, then it undergoes…

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.