16 A steering rack of a car must be able to withstand large amounts of sudden impact forces without fracturing. Which of the following properties would be the best measure of this requirement for the steering rack? (A) Ductility (B) Hardness (C) Toughness (D) Yield strength

16 A steering rack of a car must be able to withstand large amounts of sudden impact forces without fracturing. Which of the following properties would be the best measure of this requirement for the steering rack? (A) Ductility (B) Hardness (C) Toughness (D) Yield strength

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the torque (in ft.lbs.) needed to fracture a bone if: A typical human tibia is 1.5 cm inside diameter and 5 cm. outside diameter. The polar moment of inertia of this typical tibia is 60.8 cm4. Human bone has a shear modulus of G=3.5. The length of a female adolescent tibia at age 14 is 373 mm or 37.3 cm.
Please help.
can you elaborate each
Please fast answer
2 m B specimen How did you find the air resistance for the impact test experiment?
Table 1: Mechanical behavior of human cadaver tibial bones during pure torsional loads applied with the proximal tibia fixed and the torque applied to the distal tibia until there is bone fracture. Medial condyle Tibial tuberosity- Medial malleolus -Lateral condyle Head of fibula Ti-6Al-4V grade 5 Stainless Steel 316L Region of bone resection -Lateral malleolus L = 365 mm Annealed Annealed Torque at ultimate failure (bone fracture) Displacement (twist angle) at ultimate failure Torsional Stiffness Table 2: Mechanical properties of candidate materials for the rod. Material Process Yield Strength (MPa) 880 220-270 Do = 23 mm Elastic Modulus (GPa) 115 190 d₁ = 14 mm Figure 1: Representative tibia bone showing the resection region (blue arrows) and median length (L). A circular cross section of distal tibia taken at the level of resection) showing the median inner (di) and outer (Do) diameters of the cortical bone. A tibia bone after resection with the proposed metal solid rod (black line)…
When a radial load affects the bearings, deformation-crushing occurs at the contact points during the rotation movement. Explain this deformation mechanism in cylindrical roller bearings. Explain in detail how the amount of elastic deformation in cylindrical roller bearings depends on which formulas are calculated. keywordler ‘cylindrical roller bearing elastic deformation’; ‘Roller bearing elastic deformation’ , ‘Bearing Displacement’
What is the trend of the best fit line for the total energy E in your data? If the data is accurate, the total mechanical energy should decrease slightly. Why is that?
Steel springs must have a modulus of resilience of at least 2.0 MPa. What should be the minimum yield strength (in MPa) of a 10mm diameter spring used to support a load of 10,000 N if elongation is 1mm for every 100mm length?
Test Specimen 4140 CF steel 6061 T6 Al Gray Cast iron 40 FC Brass 360 Impact Energy (J or ft-lb) 48.5 ft-lb 25 ft-lb 12 ft-lb 27 ft-lb Impact Strength (J/m or ft-lb/in) 123.096 ft-lb/in 63.452 ft-lb/in What is the final analysis/ overall observation from the data? 30.457 ft-lb/in 68.528 ft-lb/in
PLEASE SOLVE THREE GIVEN SUB-PARTS i,ii,iii of the question. Accurate and exact. (i) State one mechanical material property and one non-mechanical material property that would be important in the design of a treadle. For each material property, state the units for that property and give a brief explanation of its importance in engineering terms to the design of the treadle. (ii) Propose a suitable material for the treadle. Explain your reasoning for your material selection, providing clear substantiating evidence of the materials suitability to the treadle. Your evidence should relate to the two material properties given as your answer to Part (i), but can also introduce other important factors. Provide sources of your evidence, which can be taken from EduPack or elsewhere. (iii) Explain why an Ashby chart might be useful to help selecting an appropriate material for the treadle.
Q4- Explain the following state "other mechanical properties often may be estimated from hardness data" Q5- "Engineering stress-stain curve and True stress-strain curve are similar". Why? Q6- Is it possible utilized bending test for non-brittle materials? Why? Q7- Engineering stress-strain curve for the compression test is similar to that of the tensile test. But the shape of plastic region is different. Explain why? Q8- find the yield point for brittle and ductile materials?