Homwork-3PH-1Two smooth pipes, each having a mass of 300 kg, are supported by the forked tines of thetractor in Fig. 3.10a,b. Draw the free-body diagrams for each pipe and both pipes together.B0.35 mA0.35 m30°(b)Fig. 3.10PH-2The member shown in Fig. 3-11a is pin connected at A and rests against a smoothsupport at B. Determine the horizontal and vertical components of reaction at the pin A.B80 N/m300.75 m90 N m1.5 m(a)Fig. 3.11

As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Homwork-3 PH-1 Two smooth pipes, each having a mass of 300 kg, are supported by the forked tines of the tractor in Fig. 3.10a,b. Draw the free-body diagrams for each pipe and both pipes together. 0.35 m 0.35 m 30 (b) (a) Fig. 3.10

Homwork-3 PH-1 Two smooth pipes, each having a mass of 300 kg, are supported by the forked tines of the tractor in Fig. 3.10a,b. Draw the free-body diagrams for each pipe and both pipes together. 0.35 m 0.35 m 30 (b) (a) Fig. 3.10

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.11P: A standpipe in a water-supply system (see figure) is 12 ft in diameter and 6 in. thick. Two...

See similar textbooks

Similar questions

SolveSample Problem 4.1.All remain as presented, except for the following changes.The factor ofsafety is now 2, and not 3.As Presented, the thickness of the tube is uniform. In the new one that you are solving,let the thicknessesof the top and bottom be the same,ttb, and the thicknesses of theleft and right be the same,tlr.Theheightand the width of the tube are still respectively 5 in and 3.25 in.As you make thesethickness changes,you are to keep thetotal mass of the tube unchanged. Answer the same questions (a) and (b).Explain your findings
Q2/ A belt drive consist of two V-belts in parallel, on grooved pulleys of the size. The angle of the groove is 30°. The cross – section area of each belt is 750 and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximun stress in the material is 7 MN/m?. Answer the following questions 1- The centrifugal tension in belts is (a) increases power transmitted (b) decreases power transmitted (c) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
Show Complete solutions with given.
2. The pressure of a hydraulic working cylinder is intensified by using a pressure intensifier. The intensifier have area A₁ against the pump pressure pp and area A2 against the load pressure PL. a) Calculate the pressure ratio A₁/A2 needed to lift the mass m=20000kg, when the pump pressure pp=280bar and work force resisting the piston motion Fw=100kN. The piston diameter D=80mm. pp is approximated to be constant. Losses, including the directional valve loss, are neglected. A₂ PL b) What is the lifting speed of the mass, if the pump flow Q₁ is 120 1/min.
i need the answer quickly
QUA four stroke internal combustion engine has the following specifications: Brake power 7.5 kW; Speed 1000 r.p.m.; Indicated mean effective pressure 0.35 N/mm2; Maximum gas pressure 3.5 N/mm2; Mechanical efficiency - 80 %. Determine: 1. The dimesions of the cylinder, if the length of stroke is 1.4 times the bore of the cylinder: 2. Wall thickness of the cylinder, if the hoop stress is 35 MPa: 3. Thickness of the cylinder head and the size of studs when the permissible stresses for the cylinder head and stud materials are 45 MPa and 65 MPa respectively. Any other data required for the design may be assumed.
- Two pipes, each with a diameter of Im, are supported every 10m by a frame, as shown in the figure. Each pipe (including its contents) weighs 2.0 kN/m. All contact surfaces are assumed to be frictionless. Determine the support reactions. 1.8m A 2.4 m B 2.4 m
Help
PLEASE ANSWER NUMBER 2 MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.(USE 4 DECIMAL PLACES FOR ALL YOUR COMPUTATIONS)
Q2 / A belt drive consist of two V-belts in parallei, on grooved pulleys of the same size. The angle of the groove is 30". The cross - section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximum safe stress in the material is 7 MN/m. Answer the following questions 1- The centrifugal tension in belts is . . (a) increases power transmitted (b) decreases power transmitted (e) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
Q7 Design a rocker arm of I-section made of cast steel for operating an exhaust valve of a gas engine. The effective length of the rocker arm is 250 mm and the angle between the arm is 135°. The exhaust valve is 80 mm in diameter and the gas pressure when the valve begins to open is 0.4 N/mm2. The greatest suction pressure is 0.03 N/mm below atmospheric. The initial load may be assumed as 0.05 N/mm? of valve area and the valve inertia and friction losses as 120 N. The ultimate strength of cast steel is 750 MPa. The allowable bearing pressure is 8 N/mm2 and the permissible stress in the material is 72 MPa.
A wood-stave pipe is bound by steel rods which take the untire bursting stress. Find the proper spacing for 8-mm diameter steel rod for a 1.80-m diameter wood stave pipe if the working stress is 60 mpa for a head of water of 20m.