Q3. Determine the dimensions of an I-section connecting rod for a petrol engine from the following data: Diameter of the piston = 110 mm; Mass of the reciprocating parts =2 kg; Length of the connecting rod from centre to centre 325 mm; Stroke length = 150 mm; R.P.M. 1500 with possible over speed of 2500; compression ratio = 4: 1; Maximum explosion pressure = 2.5 N/mm?. %3D %3D %3D

Q3. Determine the dimensions of an I-section connecting rod for a petrol engine from the following data: Diameter of the piston = 110 mm; Mass of the reciprocating parts =2 kg; Length of the connecting rod from centre to centre 325 mm; Stroke length = 150 mm; R.P.M. 1500 with possible over speed of 2500; compression ratio = 4: 1; Maximum explosion pressure = 2.5 N/mm?. %3D %3D %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2.2 An ideal ramjet engine is being designed for a Mach 3.2 aircraft at an altitude of 10000 m. The fuel has a heating value of 43263.6 kJ/kg, and the burner exit total temperature is 1889 K A thrust of 42258N is needed. What is the required airflow? What is the resulting nozzle exit diameter? What is the resulting TSFC and dimensionless thrust?
A 3-liter 6-cylinders square engine (bore = stroke) with two intake valves and one exhaust valve per cylinder is designed to have an output power of 300 kW and a corresponding bmep of 18.5 bar. The intake temperature is 55°C. Assume an average flow coefficient at the intake valve of 0.35. a) Calculate the intake valve area and the diameter of intake valves for a good volumetric efficiency (Mach index Z of 0.6) b) Calculate the exhaust valve area if the exhaust gases temperature is 600°C; the average flow c) The exhaust valve opens when the piston is at the bottom dead center. For a lift 1 = 1.35 cm of the coefficient at the exhaust valve is 0.6. exhaust valve, calculate the flow rate through the exhaust valve. The average flow coefficient at the exhaust valve is 0.6 and the cylinder pressure and temperature are 500 kPa and 600°C. Assume exhaust system pressure is 105 kPa. Notes: The specific heat ratio and gas constant for the gases at the inlet and exhaust valves are respectively…
2 A six-cylinder 4-stroke cycle petrol engine is to be designed to develop 250 kW of (b.p) at 2200 rpm the stroke / bore ratio is to be 1.3:1. Assuming nm =80% and an indicated mean effective pressure of 9.5 bar, determine the required bore and stroke. If the compression ratio of the engine is to be 7.5 to 1, determine consumption of petrol in kg/h and in kg/bp.hr. Take the ratio of the indicated thermal efficiency of the engine to that of the constant volume air standard cycle as 0.65 and the calorific value of the petrol as; 44770KJ/kg.
Solve asap
HANDWRITTEN: Cessna 172 Skyhawk has a horizontally opposed engine that operates on a Diesel cycle with a compression ratio of 18:1. Using the air standard assumption, the following parameters are applied: P1 = 115 kPa, k = 1.35, mep = 815 kPa. Compute for the cutoff ratio. Note: Make sure to indicate a CORRECT P-V and T-S diagram. Also, show the complete derivation of the working formula used to solve for the cut-off ratio.
A single cylinder marine engine has a compression ratio () of 6.75, a clearance volume of 1200 cm3 and a piston stroke length of 500 mm. What is the bore diameter in millimetres (mm) for the engine cylinder. Give your answer to the nearest millimetre mm.
Need careful answer on this one. Help me out please answer carefullt with step by step solution thank you so much.
Q2/ In one of applications, wanted to condition laboratory at inside design condition DBT=24 °C and 50% Rh and outside design condition DBT=44 °C and WBT=27 °C. Total sensible load for the space is 35 kW and total latent load for the space is 19 kW. Rate of supplied air to the space is 11050 m /hr and rate of outside ventilation air is 4250 m/hr. The recirculated air is mixing with the outside air and then entering to cooling coil and leaving at 95% Rh then the air is passing through heating coil before supply to the space. Determine: 1.Condition of supply air to the conditioned space (DBT & RH); 2.Condition of air before and after cooling coil (DBT & RH); 3. Sensible load of heating coil; 4.Sensible load and latent load and total load of cooling coil; 5. Apparatus dew point (ADP) for the cooling coil; 6. Draw the cycle on the psychrometric chart.
(2) a fou-cylinder, 2.4 liter engine operates on a four-stroke cycle at 3200 r.p.m. the compression ratio is 9.4:1, the connecting rod length r = 18 cm, and the bore and stroke are related as S = 1.06 B. calculate :- 3 (a) clearance volume of one cylinder in cm³,L, and in ³. (b) Bore and stroke in cm and in. (c) Average piston speed in m/seca 1 ft/sec
Please help me do this homework
(1) A four-cylinder, two-stroke cycle diesel engine with 10.9 cm bore and 12.6 cm stroke produces 88 kW of brake power at 2000 r.p.m. compression ratio rc-18:1. calculate :- (a) engine displacement. (cm³,L) (b) brake mean effective pressure. (kpa) (c) torque. (N.m) (d) clearance volume of one cylinder. (cm³) ANS: (a) 4703,4.703, (b) 561, (c) 420, (d) 69.2
(e) Calculate the angular velocity of the gas mixture sing paddle wheel model of two- cylinder engine by assuming swirl ratio is 11. Use the following data: i. air to fuel ratio 8.8 ii. compressiom ratio-7.2 ii, volunetric efficiency77 iv. indicated thermal efficiency 33 v. mechanical efficiency55 vi. brake power 62000 j/sec vii. engine volmne 1000 cm3 vi. calorific value 45000 kj/m