Homework Question: The pipe bend as in the figure below has D1 = 29 cm and D2 = 12 cm. When water at 20°C flows through the pipe at 4000 gal/ min, p1 = 215 kPa (gage). Compute the torque (magnitude and direction) required at point B to hold the bend stationary? HINT

Q: Q/ For Example 5 if the water supply pressure is 75 kg and intensify to 250 kg what will be the…

A:

Q: A liquid of a density e flows through a divergent pipe. An absolute pressure at the inlet is equal…

A: Bernoulli's principle states that the energy of the flow at the inlet of a pipe will always be equal…

Q: 2 Q2 = 10 liter/s %3D 3 DI =? Water D3 = 65mm Tank base area=1 m²

A: In the tank, some pipes are inlets and some are outlets. From inlet the water enters within the tank…

Q: Need proper handwritten correct solution. Don't give copied solution

A: Given Data The atmospheric pressure is: Patm=100 kPa The cross section area is: A=0.0026 m2 The…

Q: Problem # 3 4 ft 30° 4 kips/ ft 5 ft Given: The beam is supported by the roller at A and a pin at B.…

A: The beam is supported by the roller at A and a pin at B. To Find: The reactions at points A and B on…

Q: A turbine with a power coefficient Cp = 0.26 is able to generate 3.5 MW of electrical power with…

A:

Q: Q4:- Given = 2(G- E) where u is the velocity of water in meter per second and y the distance from…

A:

Q: For the Fig. shown, find the velocity of point 1 and the pressure of point 2 D2=20 cm

A:

Q: A water stream at pipe AB divides into two branches as shown in the figure below. The average…

A: given data; ⇒diameter of pipe A (dA)=2inch=0.0508m⇒velocity in pipe (VA)=2m/s⇒diameter of pipe C…

Q: Consider a business jet, like the Gulfstream G550, flying at a standard altitude of 30,000 and V1 =…

A: "from properties of atmosphere at high altitude" at 30000 ft , the density will be ,  ρ=0.02866 lbm…

Q: A fluid with a density of 0.8 g/cm³ is being emptied from a very large tank through a small…

A:

Q: Q4, bend. When the gauge pressure is E psi, F = 2000 lb to hold the bend in place. Determine a) the…

A:

Q: For the figure shown below, the pressure at Point 1 is 150 kN/m and at Point 2 is 190 kN/n. Find the…

A: Given data, At pressure point 1  P1 = 150 kN/m2At point 2 P2 = 190 kN/m2To determine the velocity v…

Q: * A hydraulic lift raises a total load of 8 tonnes through a height of 12 m- once in every two…

A: given; total load(m)=8 tonnes                        =8000kgfor every 2 minute.total load rate…

Q: 2. If the velocity at point A is 25 meters per second, compute for the velocity at point C and the…

A: VA=25 m/s

Q: For the Fig. shown, find the velocity of point 1 and the pressure of point 3 D2=20 cm P2=100 Kpa…

A:

Q: b) The figure below shows a plan view of a 90° bend and a reducer cast altogether in one anchor…

A:

Q: b) To slow the boat very quickly a thrust reverser (or speed brake) is deployed (as shown in the…

A: Given data :-Velocity of V1=V2= VNozzle area (a) = a2Angle = 90°Find out :-  Thrust force on the…

Q: is desired to pass water from point 1 to point 3 to run a fluid engine, pressure p1= 700kpa and…

A: Power to be Transmitted = {density * flow * ( total required head)} / efficiency total head required…

Q: 4 mm drill holes in the large water tank causing water to flow out of the tank into a single…

A: Given:dia of hole, d=4 mmh=5 mangle of deflection, θ=180°

Q: A fireboat is putting out a blaze from a beach bonfire that got out of hand. If the nozzle angle is…

A:

Q: (Problem 3) A horizontal water pipe is reduced in size from 18 inches in diameter from point A to 6…

A:

Q: 3.2 Perhaps you have felt the end of a garden hose exert a backward force on your hand if (and only…

A: Solution: Given Data: Q=1 L/s=1000 cm3/sA=1 cm2a=0.5 cm2   Note: Dear Student! As per our…

Q: A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The…

A:

Q: For the moving cart and vane in the figure below, let the jet be water of 3 in diameter at 35 ft/s.…

A:

Q: The pump in the figure shown draws water from a reservõir and discharge through a which terminates…

A:

Q: Problem-5: A Plunger is fitted to a vertical pipe filled with water. The lower end of the pipe is…

A: Givena=5 m/s2hatm=10mhv=2mg=10 m/s2

Q: Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW…

A: Given     Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW               Speed, N = 2500 rpm…

Q: For the cart in the figure shown, compute the force on the wheels caused by deflecting the jet and…

A:

Q: The pumper truck shown in the figure below is to deliver 1.7 ft³/s to a maximum elevation h of 59 ft…

A:

Q: A pump is used that has a Power Pb= 40HP and works with an efficiency of 85% to drive a flow rate Q…

A:

Q: A static thrust stands as it showed in the Figure. The intake velocity is 200 m/s, exhaust velocity…

A: Given data:-  The intake velocity = 200 m/s, exhaust velocity=500 m/s, intake cross-section area =1…

Q: Water enters a fountain through a pipe with a cross-sectional area A₁ at a flowrate Q. The pressure…

A:

Q: A stream of water, 3” in diameter, discharges into the atmosphere at a velocity 80.0 ft/sec. Find…

A:

Q: Runner shaft. Figure shows a Kaplan turbine. The flow of water rotates the runner at 200 rpm to b.…

A: Given Data  Rotation speed of the runner, N=200 rpm Shaft diameter of the runner, d=28.575 mm Radius…