Homework problem (1): A 3-phase, star connected synchronous motor of 10 kW at 1100 V has synchronous reactance of 8N per phase. State the condition at which the current is minimum, then find the minimum current drawn by the motor and the corresponding induced emf for full-load condition. The efficiency of the motor is 0.8 when neglecting armature resistance.

Homework problem (1): A 3-phase, star connected synchronous motor of 10 kW at 1100 V has synchronous reactance of 8N per phase. State the condition at which the current is minimum, then find the minimum current drawn by the motor and the corresponding induced emf for full-load condition. The efficiency of the motor is 0.8 when neglecting armature resistance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Three Phase Induction Motor Load Test, . At what load will the efficiency be maximum
Q2. For a 10 kW, 380V, three-phase, four-pole, 1200 r/min, delta-connected induction motor. Adopt a specific magnetic loading of 0.4712 Wb/m2 and a specific electric loading of 23000 ampere-conductors per metre. The motor has a full-load efficiency of 85% and a full-load power factor of 0.8. A square pole design may be assumed and the stator leakage impedance voltage drop may be ignored. Assume also that the winding is full-pitched and uniformly wound. To calculate the following design parameters (a) The approximate outer diameter and length of the rotor core (b) the air gap length of the motor (c) the turns per phase (d) the number of conductors per slot, if 3 slots per pole per phase are chosen
A 200 V dc shunt motor takes a current of 20A on a certain load. R= 12 and Rah= 2002. Find the resistance to be inserted in series with the armature to reduce the speed to 75% of its original value if the load torque is constant.
The develop motor Torque is in .N.M when frequency 60HZ and six poles * O 24 O 20 14 O 12 The Mechanical Power is .kw Which The Motor Would Develop For This Field Excitation. * 2167,34 21677.63 1495.56 11693.98
A 10 kW, 250V shunt motor has an armature resistance of 0.5ohm and a field resistance of 200ohm. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3A. At full load and rated voltage, the current line is 47A and because of armature reaction, the flux is 4% less than it no load value. (a.) What is the full load speed? (b.)What is the developed torque at full load? 1158 rpm
7-5. A 50-kW, 440-V, 50-Hz, six-pole induction motor has a slip of 6 percent when op- erating at full-load conditions. At full-load conditions, the friction and windage losses are 300 W, and the core losses are 600 W. Find the following values for full- load conditions: (a) The shaft speed n. (b) The output power in watts (c) The load torque Tload in newton-meters (d) The induced torque Tind in newton-meters (e) The rotor frequency in hertz
A3 phase, 1500 rpm, 2200 V, star connected synchronous motor having per phase impedance 0.4 + J9 ohms. On some excitation armature induces 2900 V. Find the maximum torque developed by the motor before the motor is separated from synchronism.
7-5. A 50-kW, 440-V, 50-Hz, six-pole induction motor has a slip of 6 percent when op- erating at full-load conditions. At full-load conditions, the friction and windage losses are 300 W, and the core losses are 600 W. Find the following values for full- load conditions: (a) The shaft speed n. (b) The output power in watts (c) The load torque Tloud in newton-meters (d) The induced torque Tiad in newton-meters (e) The rotor frequency in hertz
1. The rated current of 15 hp, 220V separately excited DC motor is- a) 50.87A b) 60.2 A c) 40.31A 2. If the load torque T₁ of induction motor proportional to square of the rated speed, what will be the value of load torque if the motor speed reduces to half rated speed. a) 2-TL. 3. In stator voltage control strategy of induction motor, the variable stator voltage will be: a) above rated voltage b) below than rated voltage e) above and below rated voltage
Q5:- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 a and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.