Homework// Estimate_k and a in the infiltration equation (D = ktª) (‡ in minutes and D in mm) for a water run by using the following information: Inflow (q) is 5.5 l/sec per 1 m of the width Depth of flow at the beginning of the water run is 5 cm The infiltrated depths are distributed as a parabola The recorded data of water advance are as follows: Time (t) in minutes ● 30 80

Homework// Estimate_k and a in the infiltration equation (D = ktª) (‡ in minutes and D in mm) for a water run by using the following information: Inflow (q) is 5.5 l/sec per 1 m of the width Depth of flow at the beginning of the water run is 5 cm The infiltrated depths are distributed as a parabola The recorded data of water advance are as follows: Time (t) in minutes ● 30 80

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
ΤΘ In a border-irrigation-system, the following information is given The border length is 300 m - The border width is 5 m -Qin = 18.6 l/s - Slope is 0.7% - (1 Manning's n = 0.2 The infiltration equation is D = 50.6, D in mm and t in minutes The data are shown in the following table Distance 0 30 (m) Advance 06 time (m) Recession 95 98 time (m) ☆ 60 15 ||| 90 120 150 180 25 34 48 65 80* *means that the irrigation gates have been closed at this time. If the net depth of irrigation (NDI) IS 70 mm, find the irrigation adequacy? 102 110 117 125 140 فلاتر 210 240 O 152 96 167 270 300 7 119 160 174 200 إضافة شرح... mum
The data from a stream gauging station during a measurement campaign are given below, compute the discharge in the river. Distance from left water edge 0 (m) Depth (m) Average velocity (m/sec) 0 1 1 1.0 0.25 3 2.6 0.35 5 3.1 0.5 7 2.5 0.45 9 0.9 0.3 10 lo 0 0
I have a test that I need to answer in half an hour
.
Quo Put a Circle around the CORRECT Answer 1- Given: *Length of Secondary open drain Lopen = 2400 (m). *Tile Drains Spacing, S = 80 (m). * Flow Rate of Secondary Open Drain, Qopen = 5580 (m³/d). (a) Qrile 200 (m³/s) (b)QTile = 300 (m³/s) (c) Qrile = 186 (m³/s) 2- Given: * Effective depth of the impermeable layer below Tile Drain level, *de = 12 (m). *Hydraulic conductivity of soil layer located above Tile Drains level, Ka = 6 (m/d). * Hydraulic conductivity of soil layer located below Tile Drains level, Kb = 0.5 (m/d). * Maximum height of W.T. above Tile Drains level at mid-distance Ho = 0.8 (m) *Drain Spacing S = 45 (m) Drainage Coefficient R. is: (a) 0.001 (m of water/d) (b) 0.015 (m of water/d) (c) 0.026(m of water/d) P-12 3- An agricultural farm is cultivated by mixed crops. There is no drainage system in farm. The available data are: *Leaching Requirements of the farm, LR = 37% *Depth of Irrigation Water, (dw)i = 0.081 (m of water/Irrigation) *Depth of drained water (dw) is: (a) 1…
C PART ONLY
Table Q4 shows the details of the storm hydrograph with the corresponding direct discharge. The given time interval is 3 hours between the readings. Q4 Table Q4 Excess rainfall (mm) 11 Time (hr) Direct discharge (m³/s) 3 70 28 230 9. 30 600 12 1400 15 2380 18 3300 21 4880 24 6320 27 3305 30 350 33 300 36 100 By using the convolution method, determine the unit hydrograph ordinates. (a) (b) Illustrate the unit hydrograph.
The following are the data obtained in a stream gauging operation. A current meter with a calibration equation V = (0.32 N + 0.032) m/sec was used to measure the velocity at 0.6 depth. Using the mid-section method, calculate the discharge in stream. Distance from the right bank Depth 0 2 4 6 9 12 15 18 20 22 23 24 0 0.5 1.10 1.95 2.25 1.85 1.75 1.65 1.50 1.25 0.75 0 No. of revolutions 0 80 83 131 139 121 114 109 92 85 70 0 Time (Sec) 0 180 120 120 120 120 120 120 120 120 150 0
ASAP
The water need of a district with a future population of 38800 and average daily water consumption qort = 189 lt / N / day will be met by leakage pipes fed double-sided (at the end of the collection box). Water layer thickness H = 5 m, k = 0.0018 m / s and n = 0.02 are given. Standard pipe diameters and costs are given as follows: 0.4 m (60 TL / m), 0.7 m (70 TL / m), 1.0 m (80 TL / m) and 1.3 m (85 TL / m). Size the leaking tube so that it is most economical (diameter, length and slope). Average flow velocity is between 0.2-0.4 m / s.
16