Home work/1: A fan with 24-in-diameter blades moves 2000 cfm (cubic feet per minute) of air at 70°F at sea level. Determine (a) the force required to hold the fan and (b) the minimum power input required for the fan. Choose a control volume sufficiently large to contain the fan, with the inlet sufficiently far upstream so that the gage pressure at the inlet is nearly zero. Assume air approaches the fan through a large area with negligible velocity and air exits the fan with a uniform velocity at atmospheric pressure through an imaginary cylinder whose diameter is the fan blade diameter?

Home work/1: A fan with 24-in-diameter blades moves 2000 cfm (cubic feet per minute) of air at 70°F at sea level. Determine (a) the force required to hold the fan and (b) the minimum power input required for the fan. Choose a control volume sufficiently large to contain the fan, with the inlet sufficiently far upstream so that the gage pressure at the inlet is nearly zero. Assume air approaches the fan through a large area with negligible velocity and air exits the fan with a uniform velocity at atmospheric pressure through an imaginary cylinder whose diameter is the fan blade diameter?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUIZ 1. A compressor draws in 0.25 m³/s of air whose density is 1.26 kg/m³ and discharges it with a density of 4.87 kg/m³. At the suction, P1 = 103.4 kPaa; at the discharge, P2 = 551.4 kPaa. The increase in the specific internal energy is 78.63 kJ/kg, and the heat from the air by cooling is 30.24 kJ/kg. Neglecting changes of potential and kinetic energy, determine the work on air in kW, BTU/min, and Hp. 2. Consider an underground water source whose free surface is 60 m below ground level. The water is to be raised 5 m above the ground by a pump. The diameter of the pipe is 10 cm at the inlet and 15 cm at the exit. Neglecting any heat interaction with the surrounds and frictional heating effects, determine the power input to the pump required for steady flow of work at a rate of 15 liters per second. 3. A piston cylinder arrangement contains 100 liters of saturated water and 900 liters of saturated steam in equilibrium at 1 MPaa (t,at = 179.91°C, V1 = 1.273x10° m³/kg and vạ1 =194.44x103…
Answer the followwing problem: Determine the number of stages needed for a centrifugal pump if it is used to deliver 600gal/min of water and pump power of 15Hp. Each impeller develops head of 38ft. Calculate the compressor work in kJ required to compress 1 kg of an ideal gas from an initial volume and pressure of 0.65m3 and 101.3kpa to a final pressure of 517kpa & volume of 0.1943m3.ANS. 133.549 An air compressor takes air at 97kpa at the rate of 0.4m3/s and discharges to 650kpa. If power input to the compressor is 110kw, determine the heat loss(kw) in the compressor. ANS. 11.948
Q3. In Fig. 3 below, the pump move water from tank A to pressurized Tank B at rate of 100 m³ in 5 min. Perform appropriate calculation to determine if the pump with 2.5 hp works for this purpose. Repeat the calculation and determine if the pump works with air pressure in Tank B of 2.5 atm instead 1.5 atm. в P=15 atm Presure dow lese 4m 50 m Pump Figure 3 water supply system
Q2/ A 1.343 x 10' J fan is used in a large room to provide for air cireulation. Assuming a well insulated, sealed room, determine the internal energy increase after I hour of operation.
2. For storimg purposes, water is to be moved from one pool to another that is 50 ft above the first one using a pump and an 8-in. inside-diameter pipe. The flow rate of the water is 2.5 ft’/s. There is a loss of available energy as 61 V²/2ft?/s² where Vis the average velocity of water inside the pipe. Determine the amount of shaft power required, in hp.
A pump has a displacement volume of 122 cm3. It delivers 0.0027 m3/s of oil at 1720 rpm and 85 bars. If the prime mover input torque is 175 N∙m What is the overall efficiency of the pump? What is the theoretical torque required to operate the pump?
5. Consider two tanks, A and B, each with a large opening at the top. The two tanks contain different liquids. A small hole is made in the side of each tank at the same depth h below the liquid surface, but the hole in tank A has three times the cross-sectional area of the hole in tank B. (a) If it is known that the mass flow rate is the same for the two holes, find the ratio of PALPB of the densities of the liquids in tanks A and B. (b) (c) equal volume flow rates, what height above the hole must the liquid in tank A be just then? Find the ratio RVAIRVB of the volume flow rates from the two tanks. At one instant, the liquid in tank B is 90 cm above the hole. If the tanks are to have
Q2. Design and plot a hydraulic system for drive and control aircraft flap to overcome 500 N aerodynamic forces with the following specifications:- The actuator single acting cylinder with bore diameter 25 cm , smooth pipes line has diameter and total length 15 mm and 12 m respectively, six elbows (K = 0.9), if average velocity of the oil in the pipes 20 m/s and total pressure losses across control valves and other accessories 1.4 bar. Determine total pressure pump required for hydraulic circuit. (Note:- poil =880 kg/m², voil= 64.2 mm/s)
The question is important, Answer it correctly. 1. A ventilation fan is moving 3,200 cfm with a fan static pressure of 8.30" wg. The airflow is increased to 3,500 cfm by increasing the fan speed. What is the new static pressure of the fan?
Water is contained in both sides of the cylinder system shown below and the valve is closed. If the pressure on the right hand side of the valve is 119.6 kPa, what is the height in tank B, i.e. what is hp 1? Assume that the atmospheric pressure is 100 kPa, the acceleration due to gravity is 9.807 m/s² and the density of water is 1000 kg/m³. A Po B ha,1=1.5 m Water Water hg,1 1.0 m 0.5 m Pval,left Pyal,right A) 1.0 m B) 1.5 m C) 2.0 m D) 2.5 m
2. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079ft/cu. ft and discharges it with a density of 0.304 lb/cu. ft. At the suction, P 1 = 15 Psia; atdischarge, P 2 = 80 psia. The increase in the specific internal energy is 33.8 BTU/lb and the heattransferred from the air by cooling is 13Btu/lb. Determine the work on the air in BTU/min and inhp. Neglect kinetic energy. 3 decimal in final answer pls
A well-insulated nozzle has an entrance area of 0.28 m2 and an exit area of 0.157 of m2. Air enters at a velocity of 65 m/s and leaves at 274 m/s. The exit pressure is 101 kPa and the exit temperature is 12°C. a)What is the inlet temperature? b)What is the exit density? c)What is the inlet density? d)What is the inlet Pressure? A V₁=65m $ 0. be P₁ = 101 kPa T₂ = 12°C m V₂=274™ 19 bobivan S